manualshive.com logo in svg

NEC A1160, Technical Overview

Share
Download
NEC A1160 Technical Overview Download Page 54

Components on the Front of a Cell 

 

4-8  

 

See the 

User's Guide

 for more information about the remote console interfaces. 

BIOS 

The BIOS is bootstrapping software that initializes and configures the hardware 
(processors, memory, I/O, and so on) in the partition. Running in the partition, the BIOS 
provides many configuration, setup, diagnostic, and recovery functions. 

In Express5800/A1160 systems, the BIOS is stored in the firmware hub in each cell. 

 

Server Management Software 

Server Management software enables a centralized operations environment for your 
systems. This software provides world-class data center management capabilities for 
greater business continuance and system resiliency. It can dramatically enhance the 
manageability, availability, and performance of your systems while considerably 
reducing total cost of operations. 

Server Management software simplifies system management, automates corrective and 
preventive measures to avoid system failure, and increases the reliability, scalability, 
and performance of NEC systems. 

 

Hardware Components 

Server Management software manages and monitors Express5800/A1160 systems. 
You can also use this software to monitor other Express5800 systems in your 
environment. 

Server Management software can be installed on the following hardware components: 

y

 Management 

server 

̶

 You can configure one or more management servers in your 

environment to manage your new and existing Express5800 systems. A 
management server with Server Management software is necessary in order for 
your systems to report problems to the support center using Remote Monitoring 
service requests. 

y

 Servers 

-

 You can install the Server Management software on Express5800/A1160 

servers. 

y

 Client 

workstations 

̶

 You can configure one or more client workstations to provide 

remote access to your management server. 

Figure 4-3

 shows the hardware components that run Server Management software. 

Summary of Contents for A1160































































Reviews:

No comments

Brands by name

Popular brands

Load more brands