background image

 

Fehler! Kein Text mit angegebener Formatvorlage im Dokument.

                             User Guide V01.06    

Operating the Orderman7 

Orderman GmbH (Part of NCR Corporation) 

39                               

 
 
 

12.3.2.2 Connecting the belt printer (Bluetooth pairing) 

To connect the belt printer to the handheld, proceed as follows: 

 

Switch on the belt printer. 

 

Open the Waiter Settings menu  

 

On the handheld, tap the "Printer Pairing" function in the "Waiter Settings". 

 

Tap the "Pair Printer now" function. 

 

Hold the printer close to the handheld (see figure below) 

 

The antenna used for detecting the printer is located in the upper right corner of the handheld. 
The antenna for the printer is located approximately in the center and at the front of the 
printer. 

 

If the printer is detected, the message "State: Paired" is displayed and a test printout is 
automatically created. 

Fig. 27: Connecting the belt printer 

 

 

Belt printer 

 

Orderman Handheld 

 

Printer, front 

12.3.2.3Testing the belt printer 

To test the belt printer, proceed as follows: 

 

Open the "Settings" menu

  Tap the 

"Printer Pairing"

 field. 

  Tap the 

"Test Print"

 field (test printout). 

  Check the test printout on the belt printer. 

 

Summary of Contents for NCR Orderman7SC


























































Reviews: