NCR 6001-0012-8801 Installation Instructions Manual Download Page 77

Page: 77 / 80

Ovation Installation

All cable assemblies connected to OPT Unit after being fastened to Anchor Point

6. Feed excess cabling into the electronics cavity so that the majority of the cables' slack

will be placed inside of the Dispenser Head. Re-use any existing cable restraints that
may be present. It may be necessary to use zip-ties or additional cable restraints to
secure the loose wiring.

These must be provided by the installer.

Install the OPTIC 5 Back Cover Plate

1. Place the back hatch cover (497-0517179) over the standoffs. The grounding post

should be on the left side of the door.

Caution:

Properly route cables to avoid pinching and allow a service loop inside the

cover when installing the OPTIC 5 cover.

2. Attach the cover to the standoffs with the 8 back cover captive screws.

Summary of Contents for 6001-0012-8801

















































































Search results

Summary of Contents for 6001-0012-8801

Reviews:

Related manuals for 6001-0012-8801

Brands by name

Popular brands

NCR 6001-0012-8801, Installation Instructions Manual

Search results

Summary of Contents for 6001-0012-8801

Reviews:

Related manuals for 6001-0012-8801

Brands by name

Popular brands