RV Pro 10,000 Installation
Installation Instructions
1.
Turn off the source water feeding the inlet water line.
2.
Install the female garden hose Y valve onto the outlet of
the system. Do not over tighten. The Y valve is gasket
sealed so only tighten hand tight.
3.
Connect the inlet water line to the system and connect a
garden hose* to the outlet port of the Y valve. The Y
valve has two valved male ports. The full port side is the
system outlet. The port that is fitted with an orifice type
flow restrictor is the drain port.
4.
Be sure that the drain port of the Y valve is closed. Flush
the system for 2 minutes, by partially opening the inlet
water valve, allowing the outlet water to run to drain.
5.
Close the inlet and outlet water valves, remove the
system outlet garden hose from the drain, place the unit
into position and connect the outlet line to the RV. When
installed the softener must set vertical.
6.
The system is now ready for use. Open the inlet and
outlet water valves making sure the drain valve is
closed. You may now enjoy your new softener.
*Garden hose not included. Two 4 ft. garden hoses recommended.
Regeneration
1.
Close the inlet and outlet valves and connect a garden
hose to the drain port of the Y valve. Open the drain valve
to relieve any pressure in the system.
2.
Once the pressure is relieved close the drain valve port
and remove the system from the RV.
3.
Gently tilt the system to drain some water out of the mineral
tank to create room for salt.
4.
Once a few cups of water have been drained from the
system, remove the tank head fill port, and pour 2 lbs of
sodium chloride table salt into the fill port on the head.
Use a cup of water to rinse the fill hole clean of salt
crystals and reinsert the fill plug.
5.
Allow the unit to set for 5 minutes, then turn on the inlet
valve and open the drain port on the Y valve to begin the
brine rinse process.
6.
After 20 minutes of brine rinsing the system is ready to be
installed back into the RV and is ready for use.
7.
Regeneration should be performed when the hardness
from your system exceeds 3 grains per gallon as indicated
on the supplied water test strips.
PleaSe noTe:
This system is already regenerated when you receive
it so an initial regeneration is not required. Do not remove the tank head
from the mineral tank. This may cause a loss in the ion exchange resin,
which may cause a decrease in system capacity.
Fill Port
Inlet
Outlet
Drain
Back Flushing
Twice a year, perform a back flush of the system. Back
flushing is performed by feeding water into the outlet port of
the system. Allow water to flow out of the inlet connection at
a rate of one gallon per minute. This reverse flow process
mechanically cleans the resin bed. If back flushing is being
done along with a regeneration process the back flush
should be done first.
long Term Storage
If the system is going to be idle for long periods of time per-
form a back flush then follow the regeneration process using
¼ cup of bleach or 1 pack of Watts Sani-System Solution in
lieu of table salt to perform a sanitization. When the system
is ready to be used again re-sanitize with bleach or
Sani-System Solution then regenerate with table salt.
Model
RV-PRo 10,000
Grains Capacity
10000 Grains
Resin Cubic Foot
0.33
Resin
Premium High Capacity
Size
21"H x 9"W
Weight
26 lbs.
Salt Required
2 lbs Per Regeneration
Life Span
5 Years +
Regeneration Time
20 Minutes
Warranty**
Tank: 5 Years / Head: 1 Year
Y Valve Positions
Outlet
Drain
Open
Closed
Outlet
Drain
Closed
Open
••With proper care and treatment.
