background image

Model 7815 Parcel Bench Scale User’s Manual

4

Description

The NCI Model 7815 is a digital electronic parcel
bench scale specifically designed for shipping
applications and is “Legal-for-Trade.”

The NCI Model 7815 has a standard RS-232
serial interface that enables it to be easily con-
nected to a computer or other data-processing
device.

Specifications

Capacity/Resolution

Power Supply

 Model

Capacity (lb)

Capacity (kg)

 n(max)

7815-75

150 x 0.1 lb

75 x 0.05 kg

1500, 1500 

(1)

7815-75

150 x 0.05 lb

75 x 0.02 kg

3000, 3750 

(2)

(1) F

ACTORY

 S

ET

  (T

YPE

 A

PPROVED

)     (2) S

ELECTABLE

 (N

OT

 T

YPE

 A

PPROVED

)

United States: NTEP #00-096. For use as a
Class III Device from +5º to +40ºC.

If unit is to be used as a commercial device, all
local reporting and registration requirements
must be followed.

14"L x 12.5"W x 4.2"H

UL/CSA approved. In-line power supply with 6’
cord.
INPUT: 120 VAC + 10%-15%, Standard 3 wire w/
ground
OUTPUT: 15VDC @ .3 Amps DC

60 Hz Standard

0.1 amp maximum

42° to 104°F (+5º to +40ºC)

Dimensions

Agency Approvals

Operating Temperature

Frequency

Power Requirements

Summary of Contents for 7815

























Reviews: