background image

 

 

3.

 

LED

 

INDICATION 

 

In order to display the operation modes and the current state of the system, three LEDs on the device case are used: 

SYS, GSM and NAV. 

The SYS system LED indicates the current status of the device. This LED indicates an alarm state if an alert is sent 

to subscribers by SMS, or an input is in the activated state. Also, the system LED can display the system operation in test 

mode (it is glowing for one second, is not glowing for one second). 

 

Meaning of SYS LED indication 

Tab. 3 

Type of the signal light 

Signal value 

No indication 

“Turn off ” mode 

1 flash in 4 seconds 

“Energy saving” mode  

2 flashes in 4 seconds 

“Monitoring” mode  

3 flashes in 4 seconds 

“Security” mode  

Continuous frequent flashes 

“Alarm” mode  

 

Meaning of GSM LED indication 

Tab. 4 

Type of the signal light 

Signal value 

No indication 

Built-in GSM-module is turned off.  

1 sec is glowing, 1 is not glowing 

Built-in  GSM-module  is  turned  on.  No  registration  in  the  operator's 

network 

1 short flash 

1 second off 

There  is  a  registration  in  the  cellular  network  of  the  operator.  Weak 

signal 

2 short flashes 
1 second off 

There is a registration in the cellular network of the operator. Medium 
quality signal 

3 short flashes 

1 second off 

There  is  a  registration  in  the  cellular  network  of  the  operator.  High 

quality signal 

Permanent short flashes 

Open  GPRS  session.  Attempts  to  establish  communication  with  the 

telematics server 

Constant glowing 

Connected either to the telematics server by GPRS or by voice channel 

 

Meaning of NAV LED indication 

Tab. 5 

Type of the signal light 

Signal value 

No indication 

Built-in GLONASS/GPS module is turned off 

1 sec is glowing 

1 is not glowing 

Built-in GLONASS/GPS module is turned on 

Navigation coordinates is not identified 

1 short flash 

1 second off 

Built-in GLONASS/GPS module is turned on 

Navigation coordinates is identified. Small number of satellites 

2 short flashes 

1 second off 

Built-in GLONASS/GPS module is turned on 

Navigation coordinates is identified. Average number of satellites 

3 short flashes 

1 second off 

Built-in GLONASS/GPS module is turned on 

Navigation coordinates is identified. A large number of satellites 

 

 

 

Summary of Contents for SMART S-2433


























Reviews: