background image

 

 

 

At the stage of correctness verification of the connection and settings of the device, it is not recommended to include 

actuators in the relay circuit directly. It is advisable to do this at the final stage of testing. 

30

85

86

87a

87

14

7

13

6

12

5

11

4

10

3

9

8

2

1

Fuse

(1A)

«GND»

«+»

«-»

Car battery

Diode 1N4007

Fuse

External

device

+

-

«GND»

 

 

Figure 33. Connection diagram of the relay to the outputs of the device OUT1 and OUT2 

 

 

2.7 1-Wire informational interface (IButton) connection 

 

 1-Wire controller interface (IButton) allows to connect up to four digital sensors like DS18S20 (DS18B20) to the 

device, and it can also operate with DS1990 keys or key / card readers that emulate DS1990 keys via interface 1- Wire. 

Each DS1990 key is a chip with a unique identification number stitched into it at the manufacturing plant by which 

the device identifies this sensor. 

Saving the key codes in the device’s memory allows to use identification when changing the security mode, activating 

the output with the profile set: “TM registered key indicator” and “TM key indicator”, and also necessary for operation of 

the “Immobilizer” function. 

The maximum number of stored keys - 510. 
It is also allowed to connect external readers of contactless Proximity-cards and keyfobs that have TouchMemory 

DS1990A  key  emulation  interface.  However,  such  readers,  as  a  rule,  do  not  operate  together  with  thermal  sensors 

connected to the same physical interface. 

 

 

Figure 34. TouchMemory System Key 

 

 

Figure 35. TouchMemory key contact reader 

 

 

Figure 36. Temperature sensor based on DS18S20 chip 

 

Summary of Contents for SMART S-2433


























Reviews: