background image

NAVMAN 

8120/8084 

 Fuel, AIS, & Radar Addendum

9

Radar 

Radar is the Radio Detection And Ranging 
system. Radar functions require an optional 
NAVMAN radar system to be installed. Three 
radar systems are available; 2 kW, 4 kW, or  
6 kW.
When the radar is operating, the scanner 
transmits powerful microwave radio pulses 
which are reflected back from any solid 
objects such as land masses or other boats. 
These objects are called targets and are 
shown on the radar window. 

The scanner rotates through 360° so the 
radar window shows all of the area around 
your boat within the range of the scanner, 
producing a map-like display called the PPI 
(Plan Position Indicator). 
Typically, your boat is in the centre of the 
radar window with concentric range rings 
surrounding it. The range rings help you 
to quickly estimate the distance to various 
targets. 
You can also view the radar overlaid on the 
chart screen.

Radar window

The radar window shows:

A

  Distance between each range ring (in this 

example, 1/8 nautical mile)

B

  Range of radar (in this example, shown in 

large digits)

C

  Radar rotation (in this example, North Up)

D

  Radar motion mode (in this example, 

Relative Mode)

E

  Cursor

F

  Distance and bearing to the cursor from 

the vessel position

G

  Compass ring

H

  Range ring

I

  North line (blue)

J

  Heading line (white)

K

  The bearing (in Relative, True, or Magnetic 

mode)

L

  Echo Expansion setting

M

  Interference Rejection setting

I

J

H

M

L

K

D

C

B

A

G

E

F

Summary of Contents for 8084






















Reviews: