NavLinkz r.LiNK RL3-A15 Page 18 Manual Download

Page: 18 / 20

Version 09.02.2023

HW: CAM(V100)(V20)

RL3-A15

Interface operation – external keypad

The switching of video sources is done by the interface’s external keypad.



Long press of keypad (2-3 seconds)

By long pressing the external keypad (2-3 seconds), the video interfaces witches the input
from the factory video to the inserted video sources.

Note: The interface switches after releasing the switch (after long pressure).

Factory video



V1 Left



V2 Right



factory video



…

By dip switch deactivated inputs will be skipped.

Specifications

BATT/ACC range

7V - 25V

Stand-by power drain

135mA

Power

135mA @12V

Video input

0.7V – 1V

Video input formats

NTSC

RGB-video amplitude

0.7V with 75 Ohm impedance

Temperature range

-40°C to +85°C

Dimensions Video-Box

116 x 23 x 86 mm (W x H x D)

Summary of Contents for r.LiNK RL3-A15





















Search results

Summary of Contents for r.LiNK RL3-A15

Reviews:

Related manuals for r.LiNK RL3-A15

Brands by name

Popular brands

NavLinkz r.LiNK RL3-A15, Manual

Search results

Summary of Contents for r.LiNK RL3-A15

Reviews:

Related manuals for r.LiNK RL3-A15

Brands by name

Popular brands