Nav TV NTX-54 Installation Instructions Manual Download

Page: 1 / 14

WARNING! FAILURE TO READ THESE INSTRUCTIONS MAY LEAD TO A TEMPER TANTRUM, A FAILED INSTALLATION AND AN UPSET

CUSTOMER. MOST LIKELY ALL. PLEASE DO US AND YOUR CUSTOMER A FAVOR AND READ THESE FABULOUS INSTRUCTIONS!!!!

100 NW 11

Street, Boca Raton, FL 33432 TEL 561-955-9770 FAX 561-955-9760

www.nav-tv.com

[email protected]

UCI-11C & UCI-11C + NTX54 Navigation kit

Rear view camera & Navigation solution for Dodge, Chrysler & Fiat UConnect Touch 4.3” &

8.4” systems

Overview:



Adds touch screen controlled navigation to vehicles without factory navigation



Provides a rear view camera solution for both the 4.3” and 8.4” UConnect Touch radios (camera not included)



Allows DVD video to be viewed while the vehicle is in drive (only on 8.4” DVD equipped systems)

Product Description

UCI-11C interface module

Radio T-harness

Included aftermarket LVDS cable

USB update cable

Rear view camera input cable

NTX54 navigation module*

Navigation to UCI harness*

External speaker*

GPS antenna*

*These items only included with the navigation option

Summary of Contents for NTX-54















Search results

Summary of Contents for NTX-54

Reviews:

Related manuals for NTX-54

Brands by name

Popular brands

Nav TV NTX-54, Installation Instructions Manual

Search results

Summary of Contents for NTX-54

Reviews:

Related manuals for NTX-54

Brands by name

Popular brands