background image

19

OPERATION

What to Wear

Wear rubber-soled athletic shoes. You will need the appropriate clothes for exercise that allow you to move freely.

How Often Should You Exercise

 Consult a physician before you start an exercise program. Stop exercising if you feel pain or tightness in 

your chest, become short of breath, or feel faint. Contact your doctor before you use the machine again. 

Use the values calculated or measured by the machine’s computer for reference purposes only. The heart 

rate displayed on the console is an approximation and should be used for reference only.

•  3 times a week for 30 minutes each day.
•  Schedule workouts in advance and try to follow the schedule.

Seat Adjustment

Correct seat placement encourages exercise efficiency and comfort, while reducing the risk of injury.

1.   With a Pedal in the forward position, center the ball of your foot over the center of it. Your leg 

should be bent slightly at the knee.

2.   If your leg is too straight or your foot cannot touch the Pedal, move the seat down on the upright 

bike. If your leg is bent too much, move the seat up.

Step off the bike before you adjust the seat.

Loosen and pull the adjustment knob on the seat tube. Adjust the seat to the desired height. Release 

the adjustment knob to engage the locking pin. Be sure that the pin is fully engaged and fully tighten 

the knob.  

Do not set the Seat Post position higher than the stop mark (STOP) on the tube.

To move the seat closer to, or away from the console, loosen the seat slider adjustment knob and 

pull down. Slide the seat forward or rearward to the desired position. Release the adjustment knob to 

engage the locking pin. Be sure that the pin is fully engaged and fully tighten the knob.

Handlebars Adjustment

The angle of the Handlebars can be adjusted for each user.
1.   Loosen the Handlebar Adjustment Knob until the Handlebars can be adjusted. Do not fully 

remove the Adjustment Handle from the machine.

2.   Adjust the Handlebars to the desired position, and fully tighten the Adjustment Handle Knob. 

Foot Position / Pedal Strap Adjustment

Foot pedals with straps provide secure footing to the exercise bike.

1.   Put the ball of each foot on the Pedals.
2.   Rotate the Pedals until one can be reached.
3.   Fasten the strap over the shoe.
4.   Repeat for the other foot.

Be sure toes and knees point directly forward to ensure maximum Pedal efficiency. Pedal straps 

can be left in position for subsequent workouts.

Summary of Contents for U627

































Reviews: