background image

4

Maximum User Weight:

  

 

 

150 kg (330 lbs.)

Machine Weight without Dumbbells:

    

48.1 kg (106 lbs.)

Weight of Dumbbells (supplied with IC4):

  

2.7 kg (6 lbs.)

Total Surface Area (footprint) of equipment:

   6667 cm

2

 (1033.3 in

2

)

Power Requirements  

  (Power Adapter): 

  Input Voltage:  

 

100-240V AC, 50-60Hz, 0.5A

  Output Voltage: 

 

9V DC, 1.5A

  (Arm Band 

  - supplied with IC4 and C6): 

Rechargeable lithium battery

DO NOT dispose of this product as refuse. This product is to be recycled. For 

proper disposal of this product, please follow the prescribed methods at an 

approved waste center.

77.9 cm

(30.7 in)

138.6 cm

(54.6 in)

131.6 cm

(51.8 in)

SPECIFICATIONS

Select the area where you are going to set up and operate your machine. For safe operation, the location must be on a 

hard, level surface. Keep the workout area clear 0.6m (24”) along the side used to access the machine and to the rear of 

the machine. Allow a workout area of a minimum 1.39 m x 2.00 m (54.7 in x 78.7 in).

2.00 m 

(78.7 in)

1.39 m

(54.7 in)

0.6 m

24 in

0.6 m

24 in

Summary of Contents for Schwinn 800IC


































































































Reviews: