Nauticam NA-G9 Instruction Manual Download Page 23 | Manualshive

Page: 23 / 33

background image

23

6.

Lock the camera into place by
turning the locking lever to the
“lock” position as shown.

7.

Gently push drive mode selector
downwards, ensuring the actuator
correctly engages with the drove
mode lever of the camera.

8.

Confirm that all the controls of the
housing are correctly engaged.

«
...
21
22
23
24
25
...
»

Summary of Contents for NA-G9


































Reviews:

No comments

Related manuals for NA-G9

Brand: Federal Signal Corporation Pages: 13

Brand: DataSafe Pages: 4

Brand: AA Products Pages: 8

Brand: Acclima Pages: 16

Brand: Access One Pages: 2

Brand: Accelleran Pages: 19

Brand: E-max Pages: 4

Brand: zenitech Pages: 16

Brand: DataCard Pages: 2

Brand: DataCard Pages: 24

ImageCard series

Brand: DataCard Pages: 2

ImageCard series

Brand: DataCard Pages: 2

Brand: PASCO Pages: 6

Brand: PASCO Pages: 4

CK 3000 Evolution

Brand: Parrot Pages: 2

Maintenence Kits

Brand: Generac Power Systems Pages: 1

Brand: hepco & becker Pages: 4

Tinker PIZZA-BOX/ THERMO-BOX

Brand: RIESE & MULLER Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands