background image

 

https://www.naturewater.eu 

Item 50808 and others 

Page 13 

 

 
 

   

09 2021

-1

 

 

 
 

Commissioning

 

 

After the installation, wash the filters of each stage before using the system for the first time. The steps 
are as follows: turn on the water-tap tubing ball valve

 (B)

, turn off the tank valve

 (M) 

of the water tank

 (N), 

turn on the goose-neck water-tap

 (Q),

 open the flush valve

 (L1).

 Now plug the power cord into the power 

supply socket, and the high-pressure pump

 (H)

 starts up automatically, the dirt water outlet begins to 

drain, filters of each stage are washed automatically. 
 
After having washed the tank, turn on the tank valve

 (M) 

of the water tank

 (N),

 turn off the goose-neck 

water-tap

 (Q),

 turn off the drain valve

 (L1).

 The reverse osmosis filter then begins to purify the water. 

When you use this system for the first time, let the purified water flow out from the full water tank twice, 
then the purified water is suitable for drinking. 
 
The concentrated waste water produces during pure water filtering cannot be used as drinking water. 
Re-check the system for tightness. 
 
 

Operation

 

 
After  the  installation  and  the  adjustment,  the  system  begins  to  automatically  produce  purified  water. 
Usually, turn off the goose-neck water-tap

 (Q),

 turn on the tank valve

 (M) 

of water storage tank, let the 

purified water flow into the tank. When the water storage tank is full of purified water, the system auto-
matically stops. Turn on the goose-neck water-tap

 (Q) 

to use the purified water. If using the system for 

the first time, let the water twice flow out of the tank; it is after that that the purified water can be drunk. 
 

 Notes: 

A)  When you use the system for the first time, turn on the goose-neck water-tap to drain the water 

(black water flowing out from water-tap caused by activated carbon filter). 

B)  When you use the system for the first time, TDS test data may be a bit high; continue washing 

until the TDS test data normalizes. 

C)  When you use the system for the first time, the purified water is not drinkable until steps A and 

B are done. The concentrated dirt water used for the water purifying process cannot be used 
for drinking. 

 

 

Summary of Contents for NW-RO50-D1

















Reviews: