National 3425 Instruction Manual Download Page 32

Page 32

National Flooring Equipment, Inc. (National) warrants to the first consumer/purchaser that this National
brand product (the #3425 Floor Prep System), when shipped in its original container, will be free from
defective workmanship and materials and agrees that it will, at its option, either repair the defect or
replace the defective product or part thereof at no charge to the purchaser for parts or labor for the
period(s) set forth below.

This warranty does not apply to any appearance items of the product, to the additional excluded items set
forth below, or to any product, the exterior of which has been damaged or defaced, which has been
subjected to misuse, abnormal service or handling, or which has been altered or modified in design or
construction.

In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth
below and provide proof of purchase to National.

The limited warranty described herein is in addition to whatever implied warranties may be granted to
purchasers by law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIODS FROM THE DATE OF
PURCHASE AS SET FORTH BELOW. Some states do not allow time limitations on an implied warranty,
so the above limitation may not apply to you.

Neither the sales person of the seller, nor any other person, is authorized to make any other warranties
other than those described herein, or to extend the duration of any warranties beyond the time period
described herein on behalf of National.

The warranties described herein shall be the sole and exclusive warranties granted by National and shall
be the sole and exclusive remedy available to the purchaser. Correction of defects in the manner and for
the period of time described herein, shall constitute complete fulfillment of all liabilities and
responsibilities of National to the purchaser with respect to the product and shall constitute full
satisfaction of all claims, whether  based on contract, negligence, strict liability or otherwise. In no event
shall National be liable, or in any way responsible for any damage or defects in the product which were
caused by repairs or attempted repairs performed by anyone other than National. Nor shall National be
liable, or in any way responsible, for any incidental or consequential, economics or property damage.
Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion
may not apply to you.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.

WARRANTY PERIOD

The National #3425 Floor Prep System is guaranteed to be free of manufacturer defective workmanship
and in  quality of materials for a period of one year. 

Items excluded from warranty coverage, unless found and reported defective immediately upon removal
from the original shipping container and before being used by the original purchaser.

A freight damage claim must be filed with the carrier by the purchaser, the shipper cannot file the freight
claim.

To obtain service contact National Flooring Equipment, Inc. toll free at 800-245-0267 for a repair
authorization number. COD freight returns will not be accepted. Freight collect shipments will not be
accepted. Warranty repairs must be accompanied by date of purchase receipt and a return/repair
authorization number.

GUARANTEE

072011

Summary of Contents for 3425


































Reviews: