background image

NI Switches Getting Started Guide

10

ni.com

Install and configure the controller as described in its documentation. Refer 
to the 

DAQ Quick Start Guide 

for information about installing an E Series 

or NI 4021 device and to the

NI Digital Multimeters Getting Started Guide

 

for information about installing the NI 4060/407

x

.

Installation

After you have installed and configured the controller, refer to the 
flowchart in Figure 3 for your next steps. 

Caution

Make sure the chassis is powered off. SCXI modules are not hot-swappable. 

Adding or removing modules while the chassis is powered on can result in blown chassis 
fuses or damage to the chassis and modules.

Table 1.  

SCXI Controllers and Supported SCXI Switches

Rear 

Connector

Switch Module

SCXI Switch Controllers

NI 4021

NI 4060

NI 407

x

E Series

10-pin

SCXI-1127

SCXI-1359 kit

SCXI-1357 kit or 
SCXI-1358 kit or 
SCXI-1359 kit

SCXI-1357 kit or 
SCXI-1358 kit or 
SCXI-1359 kit

Can control but not 
directly cable to 
switch module

2

SCXI-1128

SCXI-1129

SCXI-1130

Not supported

1

SCXI-1166

SCXI-1167

SCXI-1169

SCXI-1193

50-pin

SCXI-1160

3

SCXI-1362 kit

SCXI-1362 kit

SCXI-1362 kit

SH6868-EP and 
SCXI-1349

SCXI-1161

3

SCXI-1163R

SCXI-1190

SCXI-1191

SCXI-1192

1

 The NI 4060 can control only the SCXI-1127/1128/1129/1160/1161/1163R/1190/1191/1192 switch modules configured 

under 

Traditional NI-DAQ Devices

 in MAX. For software support information, refer to Table 2.

2

 An E Series device can control these switches when cabled to another SCXI module in the same chassis. The cabled SCXI 

module can be an SCXI signal conditioning device or another SCXI switch module. Alternatively, you can install the E Series 
device in the rightmost PXI slot of a PXI-1010 or PXI-1011 chassis.

3

 To use this module with the listed controllers, set jumpers W2, W3, and W4 on the switch module to MIO. Refer to the 

NI SCXI-1160/1161 Jumpers Note to Users

 or the 

NI Switches Help

.

Summary of Contents for SCXI-1127

































Reviews: