![background image](http://html1.mh-extra.com/html/national-instruments/scxi-1100/scxi-1100_user-manual_3426713118.webp)
Index
Index-2
© National Instruments Corporation
rear connections, E-9
SCXI-1302 50-pin terminal block
installation, E-11
wiring procedure, E-10 to E-11
SCXI-1340 cable assembly
description of, E-1 to E-2
installation, E-2 to E-3
pinout equivalences, E-2
SCXI-1341 Lab-NB/Lab-PC/Lab-PC+
cable assembly
description of, E-3 to E-4
installation, E-4
pin translations, E-4
SCXI-1342 PC-LPM-16 cable assembly
description of, E-5
installation, E-6
pin translations, E-5
SCXI-1343 rear screw terminal adapter
installation, E-13
overview, E-13
pin connections, E-14
SCXI-1344 Lab-LC cable assembly
description of, E-3 to E-4
installation, E-4
pin translations, E-4
SCXI-1350 multichassis adapter
installation, E-13
overview, E-12
SCXI-1351 one-slot cable extender
AT-MIO-16D and AT-MIO-64F-5
connection, E-6 to E-7
installation, E-12
overview, E-12
CAL/ENM* bit, 4-4
calibration
analog and timing circuitry, 3-12 to 3-13
auto-calibration, 3-12 to 3-13
capacitors
installing, 2-10
user-defined input filter capacitors, 2-9
CGND signal, 2-13, D-2
CH0- through CH31- signal, 2-13, D-2
CH0+ through CH31+ signal, 2-13, D-2
CHAN<4..0> bit, 4-4
chassis address, changing, 2-26
CHS<4..0> bit, 4-7
CHSGND signal, 3-5, C-3
CJR. See cold-junction reference (CJR).
CLKEN bit, 4-8
CLKOUTEN bit, 4-4
CLKSELECT bit, 4-4
CNT<3..0> bit, 4-9
cold-junction reference (CJR)
included on SCXI-1100, 1-1
specifications, A-3
common-mode rejection ratio
specifications, A-2
communication signals
communicating on Serial Peripheral
Interface (SPI) bus, 2-26
DAQD*/A, 2-26 to 2-29
SERCLK, 2-26 to 2-29
SERDATIN, 2-26 to 2-29
SERDATOUT, 2-26 to 2-29
SLOT0SEL*, 2-26 to 2-29
SS* timing relationships, 2-26 to 2-29
configuration. See also signal connections.
analog configuration
filter selection, 2-7 to 2-8
grounding, shielding, and output
mode selection, 2-6 to 2-7
input filtering and current loop
receivers, 2-9 to 2-10
jumper W1, 2-7
jumper W10, 2-6 to 2-7
jumpers W2 through W4, 2-7 to 2-8
jumpers W7 and W8, 2-8 to 2-9
output selection, 2-8 to 2-9
reference mode selection, 2-7
user-defined current receiver
resistors, 2-10
user-defined input filter
capacitors, 2-9
digital signal connections, 2-3 to 2-5
jumper settings (illustration), 2-5
jumper W5, 2-3 to 2-4
jumper W9, 2-4
jumper W11, 2-4 to 2-5
fixed jumpers, 2-3
parts locator diagram, 2-2
user-configurable jumpers, 2-3
Configuration Register
description of, 4-3 to 4-5
digital control circuitry, 3-8
write timing diagram, 2-29
writing slot select number, 2-28
writing to registers, 5-1
connections. See signal connections.
connector-and-shell assembly
assembly steps, 2-17 to 2-18
illustration, 2-18
cross talk specifications, A-2
current loop receivers, 2-9 to 2-10
customer communication, xiii, G-1
CV/ZERO* bit, 4-4
D