National Instruments SCC Series User Manual Download

Page: 1 / 36

background image

SCC Quick Start Guide

This document explains how to install and configure National Instruments
SCC modules with NI-DAQmx. This document assumes you have already
installed, configured, and tested the data acquisition (DAQ) device you will
connect to the SC-2345/2350 carrier. SCC modules work with NI M Series,
E Series, and B Series DAQ devices. If you have not done so, follow the
instructions in the

DAQ Quick Start Guide

included with the DAQ device

before continuing.

Contents

Conventions ............................................................................................ 2
Measurement System Overview ............................................................. 3
Step 1. Unpack the Carrier and Modules ................................................ 4
Step 2. Verify the Components ............................................................... 5
Step 3. Cable the SC-2345/2350 Carrier to the DAQ Device................. 6
Step 4. Set Up the SC-2345/SC-2350 Carrier......................................... 8

Procedure 1: Install the Connectors and Panelettes ......................... 8
Procedure 2: Apply I/O Panelette Labels ........................................ 9

Step 5. Connect the Signals..................................................................... 10

SC-2350: Connecting TEDS Sensors .............................................. 11
Connecting Digital Signals (Optional) ............................................ 12

SCC Module Installation Considerations................................................ 13

SC-2345 Carrier Considerations ...................................................... 15
SC-2350 Carrier Considerations ...................................................... 17

Step 6. Install the Modules...................................................................... 19
Step 7. Launch Measurement & Automation

Explorer (MAX)................................................................................... 22

Step 8. Configure the SC-2345/2350 ...................................................... 22
Step 9. Configure the SCC Modules ....................................................... 24

SC-2350: Configure TEDS .............................................................. 25

Step 10. Configure Channels and Tasks ................................................. 26

Configure a Task.............................................................................. 26
Configure Global Channels in NI-DAQmx ..................................... 31

Step 11. Use Your Task in an Application.............................................. 32
Getting Started Developing an Application ............................................ 33

Using Examples ............................................................................... 33
Information about Measurement Applications and Devices............ 34
Worldwide Technical Support ......................................................... 35

1
2
3
...
»

Summary of Contents for SCC Series





































Reviews:

No comments

Related manuals for SCC Series

Brand: ABB Pages: 2

FEPL-02 Ethernet POWERLINK

Brand: ABB Pages: 2

Brand: ABB Pages: 52

Brand: ABB Pages: 6

Relion 615 series

Brand: ABB Pages: 136

Relion 670 series

Brand: ABB Pages: 760

Brand: ABB Pages: 56

ACS850-04 series

Brand: ABB Pages: 296

Brand: ABB Pages: 320

Brand: ABB Pages: 17

Brand: ABB Pages: 104

Brand: ABB Pages: 370

Brand: ABB Pages: 2

FPBA-01 PROFIBUS DP

Brand: ABB Pages: 2

615 Series ANSI

Brand: ABB Pages: 60

Brand: S&C Pages: 40

Brand: Watts Pages: 2

Brand: Mako Networks Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands