National Instruments PXIe-8840 Quad-Core User Manual Download | Manualshive

Page: 4 / 38

background image

Figure 1.

NI PXIe-8840 Quad-Core Block Diagram

Intel

8 Series

PCH

Processor

Intel Core

i7

SO-DIMM

DDR3L SDRAM

PC3 12800

DisplayPort

Memory Bus Ch. A

ExpressCard/34 Slot

(ExpressCard

Variant Only)

x1 PCIE

USB

USB 2.0 x4

SATA

Hard Disk

FLASH

Watchdog

Trigger

SMB

Connector

UART

COM1

x8

PXI

Triggers

GPIB

Controller

GPIB

Connector

USB 2.0 x4

Intel I217-LM

Gigabit

PHY

RJ45

Port 1

SATA

x4 DMI2

x4 DDI

LPC

PCI Express

Switch

PXI

Express

4x4

Intel I210-IT

Gigabit

MAC/PHY

RJ45

Port 2

x1 PCIE

SPI

PCI

DisplayPort

USB 3.0 x2

USB 3.0 x2

x1 PCIE

x4 DDI

The NI PXIe-8840 Quad-Core consists of the following logic blocks on two circuit card
assemblies (CCAs):
•

The

processor

is an Intel

®

Core

™

i7 5700EQ processor (6 MB Cache, 2.6 GHz). The

processor connects to the SO-DIMM block through the DDR3L interface supporting up
to 1600 MHz SO-DIMMs and the PCH through a x4 DMI2 (Direct Media Interface)
interface supporting up to 5 GT/s per lane.

•

The

SO-DIMM block

consists of one 64-bit DDR3L SDRAM socket that can hold up to

8 GB of memory.

•

The processor provides the DisplayPort interface that connects to display peripherals on
the NI PXIe-8840 Quad-Core, and the PCI Express interface to the PXI Express
backplane through a PCI Express switch.

•

The

Platform Controller Hub

(PCH) provides the USB, PCI Express x1, and LPC

interfaces that connect to the peripherals on the NI PXIe-8840 Quad-Core.

•

The

DisplayPort

block consists of two DisplayPort connectors.

•

The

USB

block consists of four Hi-Speed USB 2.0 connectors and two SuperSpeed USB

3.0 connectors.

•

The

GPIB

block contains the GPIB interface.

4

|

ni.com

|

NI PXIe-8840 Quad-Core User Manual

«
...
2
3
4
5
6
...
»

Summary of Contents for PXIe-8840 Quad-Core







































Reviews:

No comments

Related manuals for PXIe-8840 Quad-Core

Brand: Eaton Pages: 50

Brand: Aalborg Pages: 128

Brand: CAME Pages: 32

Brand: Babybee Prams Pages: 21

Brand: QCON Pages: 4

Brand: GBD Pages: 68

Brand: Federal Signal Corporation Pages: 60

Brand: FASTRON. Pages: 16

Brand: Gardena Pages: 14

Brand: Gardena Pages: 8

Brand: IBM Pages: 276

Brand: IBM Pages: 32

Brand: IBM Pages: 157

IntelliZone2 MasterStat

Brand: Water Furnace Pages: 44

Brand: CAME Pages: 2

Brand: Fox Pages: 5

Brand: Game ready Pages: 24

Brand: Paradox Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands