background image

Electromagnetic Compatibility

This product meets the requirements of the following EMC standards for electrical equipment
for measurement, control, and laboratory use:

EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity

EN 55011 (CISPR 11): Group 1, Class A emissions

EN 55022 (CISPR 22): Class A emissions

EN 55024 (CISPR 24): Immunity

AS/NZS CISPR 11: Group 1, Class A emissions

AS/NZS CISPR 22: Class A emissions

FCC 47 CFR Part 15B: Class A emissions

ICES-001: Class A emissions

Note

 

In the United States (per FCC 47 CFR), Class A equipment is intended for

use in commercial, light-industrial, and heavy-industrial locations. In Europe,
Canada, Australia, and New Zealand (per CISPR 11), Class A equipment is intended
for use only in heavy-industrial locations.

Note

 

Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical

equipment that does not intentionally generate radio frequency energy for the
treatment of material or inspection/analysis purposes.

Note

 

For EMC declarations, certifications, and additional information, refer to the 

Online Product Certification

 section.

CE Compliance 

This product meets the essential requirements of applicable European Directives, as follows:

2014/35/EU; Low-Voltage Directive (safety)

2014/30/EU; Electromagnetic Compatibility Directive (EMC)

Online Product Certification

Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance
information. To obtain product certifications and the DoC for this product, visit 

ni.com/

certification

, search by model number or product line, and click the appropriate link in the

Certification column.

Environmental Management

NI is committed to designing and manufacturing products in an environmentally responsible
manner. NI recognizes that eliminating certain hazardous substances from our products is
beneficial to the environment and to NI customers.

For additional environmental information, refer to the 

Minimize Our Environmental Impact

web page at 

ni.com/environment

. This page contains the environmental regulations and

16

  | 

ni.com

  | 

PXIe-6570 Specifications

Summary of Contents for PXIe-6570



















Reviews: