National Instruments NI SCXI-1336 User Manual Download Page 27

Page: 27 / 83

Chapter 1

Installing and Configuring the SCXI-1129

SCXI-1129 User Manual

1-18

ni.com

DMM in PXI Slots 1 through 3 Configuration

To install your DMM in PXI slots 1 through 3, follow these steps:

Install your DMM in any one of the PXI slots 1 through 3.

In the SCXI subsystem, install the 2-slot HVAB-backplane adapter
behind SCXI slots 3 and 4.

Install additional 1-slot HVAB-backplane adapters behind SCXI
slots 1 and 2 if needed.

Install the 8-position HVAB plugs to connect the HVAB-backplane
adapters as needed.

Connect the HV8-BAN4 cable from the DMM to the HVAB connector
behind SCXI slot 4.

Connect the SH9MD-9MD cable from the DMM to the AUX IN
connector.

You can install any additional SCXI-1129 modules in any slot that has
an HVAB-backplane adapter behind it.

DMM in PXI Slot 4 Configuration

To install your DMM in slot 4 follow these steps:

Install your DMM in slot 4.

Install the 2-slot HVAB-backplane adapter behind slots 3 and 4.

Install additional 1-slot HVAB-backplane adapters behind slots 1
and 2 if needed.

Install the 8-position HVAB plugs to connect the HVAB-backplane
adapters as needed.

Connect the HV8-BAN4 cable from the DMM to the HVAB connector
behind slot 4.

You can install any additional SCXI-1129 modules in any slot that has
an HVAB-backplane adapter behind it.

Note

The SH9MD-9MD is not required for this configuration.

Summary of Contents for NI SCXI-1336




















































































Search results

Summary of Contents for NI SCXI-1336

Reviews:

Related manuals for NI SCXI-1336

Brands by name

Popular brands

National Instruments NI SCXI-1336, User Manual

Search results

Summary of Contents for NI SCXI-1336

Reviews:

Related manuals for NI SCXI-1336

Brands by name

Popular brands