background image

NI sbRIO-961x/9612XT/963x/9632XT/964x/9642XT

50

ni.com

Environmental

The NI sbRIO-96

xx

/96

x

2XT is intended for indoor use only.

Ambient temperature in enclosure
(IEC 60068-2-1, IEC 60068-2-2)

NI sbRIO-961

x

/963

x

/964

x

...............–20 to 55 °C

NI sbRIO-96

x

2XT ...........................–40 to 85 °C

Storage temperature
(IEC 60068-2-1, IEC 60068-2-2) ...........–40 to 85 °C

Operating humidity
(IEC 60068-2-56) ...................................10 to 90% RH, noncondensing

Storage humidity (IEC 60068-2-56).......5 to 95% RH, noncondensing

Maximum altitude...................................2,000 m

Pollution Degree (IEC 60664) ................2

Indoor use only

Physical Characteristics

Torque for screw terminals on J3 ...........0.5 to 0.6 N · m 

(4.4 to 5.3 lb · in.)

Weight

NI sbRIO-961

x

/9612XT ..................266.5 g (9.4 oz)

NI sbRIO-963

x

/9632XT ..................269.3 g (9.5 oz)

NI sbRIO-964

x

/9642XT ..................292.0 g (10.3 oz)

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for NI sbRIO-961 Series























































Reviews: