manualshive.com logo in svg

National Instruments NI sbRIO-961 Series, User Manual

Share
Download
National Instruments NI sbRIO-961 Series User Manual Download Page 40

©

 National Instruments Corporation

39

NI sbRIO-961x/9612XT/963x/9632XT/964x/9642XT

Analog Input

All voltages are relative to AI GND unless otherwise noted.

Number of channels ............................... 32 single-ended or

16 differential analog input 
channels

ADC resolution ...................................... 16 bits

Differential nonlinearity......................... No missing codes guaranteed

Integrated nonlinearity ........................... Refer to the 

AI Absolute Accuracy 

Tables and Formulas

Conversion time ..................................... 4.00 

μ

s (250 kS/s)

Input coupling ........................................ DC

Nominal input ranges ............................. ±10 V, ±5 V, ±1 V, ±0.2 V

Minimum overrange
(for 10 V range)...................................... 4%

Maximum working voltage for analog inputs
( common mode) ....................... Each channel must remain within 

±10.4 V of common

Input impedance (AI-to-AI GND)

Powered on ..................................... >10 G

Ω

in parallel with 100 pF

Powered off/overload...................... 1.2 k

Ω

min

Input bias current ................................... ±100 pA

Crosstalk (at 100 kHz)

Adjacent channels ........................... –65 dB

Non-adjacent channels .................... –70 dB

Small-signal bandwidth.......................... 700 kHz

Overvoltage protection

AI channel (0 to 31) ........................ ±24 V (one channel only)

AISENSE ........................................ ±24 V

CMRR (DC to 60 Hz) ............................ 92 dB

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for NI sbRIO-961 Series























































Reviews:

No comments

Brands by name

Popular brands

Load more brands