manualshive.com logo in svg

National Instruments NI sbRIO-961 Series, User Manual

Share
Download
National Instruments NI sbRIO-961 Series User Manual Download Page 34

©

 National Instruments Corporation

33

NI sbRIO-961x/9612XT/963x/9632XT/964x/9642XT

If you add heat sinks to the output transistors U49–U56 and U110–U117, 
such that the measured case temperature of the transistors remains below 
65 °C at ambient temperature of 55 °C, each channel can drive up to 1.5 A. 
However, the total current through all channels must not exceed 20 A.

1

 Use 

a heat sink that dissipates 0.5 W for each transistor driving up to 1.5 A. For 
example, for four transistors, each driving 1.5 A, use a 2 W heat sink. 
Table 5 shows the channels associated with the output transistors.

1   

The 20 A total-current limit is based on the maximum current rating of the DSUB connector pins, 5 A, multiplied by 4, the 
number of V

sup

 pins.

Table 5.  

Transistors Associated with DO Channels

DO Channels

Transistor

0, 1

U49

2, 3

U50

4, 5

U51

6, 7

U52

8, 9

U53

10, 11

U54

12, 13

U55

14, 15

U56

16, 17

U117

18, 19

U116

20, 21

U115

22, 23

U114

24, 25

U113

26, 27

U112

28, 29

U111

30, 31

U110

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for NI sbRIO-961 Series























































Reviews:

No comments

Brands by name

Popular brands

Load more brands