manualshive.com logo in svg

National Instruments NI sbRIO-961 Series, User Manual

Share
Download
National Instruments NI sbRIO-961 Series User Manual Download Page 23

NI sbRIO-961x/9612XT/963x/9632XT/964x/9642XT

22

ni.com

POWER LED

The POWER

 

LED is lit while the NI sbRIO device is powered on. This 

LED indicates that the 5 V and 3.3 V rails are stable.

STATUS LED

The STATUS LED is off during normal operation. The NI sbRIO device 
indicates specific error conditions by flashing the STATUS LED a certain 
number of times as shown in Table 3.

Table 3.  

Status LED Indications

Number of 

Flashes

Indication

1

(one flash every 
couple seconds)

The device is unconfigured. Use MAX to configure 
the device. Refer to the

 Measurement & Automation 

Explorer Help

 for information about configuring the 

device.

2

The device has detected an error in its software. This 
usually occurs when an attempt to upgrade the 
software is interrupted. Reinstall software on the 
device. Refer to the 

Measurement & Automation 

Explorer Help

 for information about installing 

software on the device.

3

The device is in safe mode because the SAFE MODE 
DIP switch is in the ON position. Refer to the 

Configuring DIP Switches

 section for information 

about the SAFE MODE DIP switch.

4

The device software has crashed twice without 
rebooting or cycling power between crashes. This 
usually occurs when the device runs out of memory. 
Review your RT VI and check the device memory 
usage. Modify the VI as necessary to solve the 
memory usage issue. 

Continuous 

flashing or solid

The device has detected an unrecoverable error. 
Format the hard drive on the device. If the problem 
persists, contact National Instruments.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for NI sbRIO-961 Series























































Reviews:

No comments

Brands by name

Popular brands

Load more brands