background image

NI 9217 Operating Instructions and Specifications

2

ni.com

This doc

u

ment describes how to 

u

se the National Instr

u

ments 9217 

and incl

u

des specifications and terminal assignments for the 

NI 9217. Visit 

ni.com/info

 and enter 

rd

s

oftwarever

s

ion

 to 

determine which software yo

u

 need for the mod

u

les yo

u

 are 

u

sing. 

For information abo

u

t installing, config

u

ring, and programming 

the system, refer to the system doc

u

mentation. Visit 

ni.com/info

 

and enter 

c

s

erie

s

doc

 for information abo

u

t C Series 

doc

u

mentation.

Note

The safety g

u

idelines and specifications in this 

doc

u

ment are specific to the NI 9217. The other 

components in the system might not meet the same safety 
ratings and specifications. Refer to the doc

u

mentation for 

each component in the system to determine the safety 
ratings and specifications for the entire system. Visit 

ni.com/info

 and enter 

c

s

erie

s

doc

 for information 

abo

u

t C Series doc

u

mentation.

Safety Guidelines

Operate the NI 9217 only as described in these operating 
instr

u

ctions.

Summary of Contents for NI 9217





























Reviews: