1
2
3
4
H3C SecPath F5010/F5020/F5040 Firewall Installation Quick Start-6W105
H3C SecPath F5010/F5020/F5040
防火墙 快速安装指南
-6W105
Tool List
工具参考
The installation tools are not provided with the firewall. Prepare them yourself.
防火墙不随机提供安装工具，请用户根据实际安装需求自备安装工具。
Introduction to Installation Accessories
安装附件介绍
Wear an ESD-preventive wrist strap, and make sure the wrist strap makes good
skin contact and is well grounded.
操作者需佩戴防静电腕带，确保防静电腕带与
皮肤良好接触，并确认防静电腕带已经良好接地。
Phillips screwdriver
十字螺丝刀
Needle-nose pliers
尖嘴钳
Wire-stripping pliers
剥线钳
Diagonal pliers
斜口钳
Marker
记号笔
Flat-blade screwdriver
一字螺丝刀
Wire crimper
压线钳
ESD-preventive wrist strap
防静电腕带
Mounting bracket
(required)
挂耳
(
标配
)
Rubber pads
(required)
胶垫贴
(
标配
)
Grounding cable
(required)
地线
(
标配
)
Cage nut
(user supplied)
浮动螺母
(
用户自备
)
M6 screw
(user supplied)
M6
螺钉
(
用户自备
)
Removable cable tie
(user supplied)
可拆卸式扎带
(
用户自备
)
Bail latch
(required)
电源卡钩
(
标配
)
M4 countersunk-head
screw (required)
M4
沉头螺钉
(
标配
)
!
Attach the rubber pads to the four round holes in the
chassis bottom. Place the firewall with upside up on
the workbench.
粘贴胶垫到防火墙底部，将带胶垫贴
的防火墙平放到工作台上。
Mounting the Firewall to a Workbench
安装防火墙到工作台
Make sure the workbench is sturdy and well grounded. Avoid placing heavy objects
on the firewall.
保证工作台的平稳与良好接地，并且不要在防火墙上放置重物。
!
Airflow of the Firewall
防火墙的风道设计
Make sure the air inlet and outlet vents are not blocked and the installation site
has a good ventilation system.
请确保防火墙的进、出风孔不被遮挡，并将防火墙
安装在具有良好通风散热系统的环境中。
The firewall adopts left-to-right air aisles.
防火墙采用左进右出的风道设计。
The F50X0 series includes the F5010, F5020, and F5040.The installation
procedures for these firewalls are similar.This guide uses the F5020 as an
example. F50X0
系列包含
F5010/F5020/F5040
款型，各款型安装方式类似，本手
册仅以安装
F5020
方式举例说明。
Attach the mounting brackets to the firewall.
安装防火墙的挂耳。
Mounting the Firewall to a Rack
安装防火墙到机柜
To avoid bodily injury and firewall damage, use at least two people to mount the
firewall to the rack because the firewall is heavy.
由于防火墙较重，安装到机柜时
至少需两人配合完成，以免造成防火墙及人身伤害。
Place the firewall in the rack and secure the firewall to the rack posts with M6 screws.
将防火墙安装进机柜中，用
M6
螺钉将防火墙固定在机柜上。
!
Mark the positions of the cage nuts
on the rack post by using a
mounting bracket.
用挂耳比对出机
柜立柱方孔条上浮动螺母的位置，
并用记号笔标出。
Install the cage nuts to the marked
positions on the rack post.
安装浮动螺母。
A cage nut is installed to the rack
post.
浮动螺母安装完毕。
1
2
3
!
