National Instruments NI-5761 User Manual And Specifications Download Page 3

Page: 3 / 25

NI 5761R User Guide and Specifications

ni.com

Front Panel and Connector Pinouts

Front Panel

Table 1 shows the front panel connector and signal descriptions for the NI 5761. Refer to the

Specifications

section of this document for additional signal information.

Caution

To avoid permanent damage to the NI 5761, disconnect all signals connected to the NI 5761

before powering down the module, and only connect signals after the adapter module has been
powered on by the NI FlexRIO FPGA module.

Table 1.

NI 5761 Front Panel Connectors

Device Front Panel

Connector

Signal Description

AUX I/O

Refer to Table 2 for the signal names and descriptions.

D<0..3>

LEDs for custom configuration.

CLK IN

Provides the NI 5761 with an external Sample clock or
Reference clock.

TRIG

Trigger input channel.

CH 0

Analog input channels <0..3>.

CH 1

CH 2

CH 3

NI 5761

250 MS/s

Analog Input

CLK IN

TRIG

CH 0

CH 1

CH 2

CH 3

UX I/O

Summary of Contents for NI-5761


























Search results

Summary of Contents for NI-5761

Reviews:

Related manuals for NI-5761

Brands by name

Popular brands

National Instruments NI-5761, User Manual And Specifications

Search results

Summary of Contents for NI-5761

Reviews:

Related manuals for NI-5761

Brands by name

Popular brands