background image

Contents

©

 National Instruments Corporation

ix

VXI/VME-PCI8026 for Linux

VXI/VME Shared Memory.................................................................6-4
Resource Manager...............................................................................6-4

Resource Manager Delay......................................................6-4

Device Configuration Editor .............................................................................6-5

Default Controller (LA –1) .................................................................6-5
System IRQ Level ...............................................................................6-5
Servant Area Size................................................................................6-5
Number of Handlers............................................................................6-6
Number of Interrupters........................................................................6-6
Protocol Register.................................................................................6-6
Read Protocol Response......................................................................6-6

Bus Configuration Editor ..................................................................................6-7

MXI Bus..............................................................................................6-7

MXI System Controller ........................................................6-7
MXI Bus Timeout.................................................................6-7
MXI CLK10 .........................................................................6-8
MXI Transfer Limit ..............................................................6-8
MXI-2 Auto Retry ................................................................6-8
A24/A32 Write Posting ........................................................6-9

PCI Bus ...............................................................................................6-9

User Window and Driver Window .......................................6-9
Expansion ROM ...................................................................6-10

VXI/VME-MXI-2 Configuration Editor .........................................................................6-10

LA Selection and Logical Address....................................................................6-11
Address Space and Requested Memory ............................................................6-11
A16 and A24/A32 Write Posting ......................................................................6-12
Interlocked Mode...............................................................................................6-12
VXI/VME Bus Options .....................................................................................6-14

VMEbus System Controller ................................................................6-14
VXI/VME Bus Timeout Value ...........................................................6-14

VXI/VME Auto Retry ..........................................................6-15
Transfer Limit.......................................................................6-15
Arbiter Type .........................................................................6-15
Request Level .......................................................................6-16
VXI/VME Fair Requester.....................................................6-16
Arbiter Timeout ....................................................................6-16

MXI Bus Options ..............................................................................................6-16

MXI Bus System Controller ...............................................................6-17
MXI Bus Timeout Value.....................................................................6-17
Advanced MXI Settings......................................................................6-17

MXI Auto Retry....................................................................6-17
Transfer Limit.......................................................................6-18
Parity Checking ....................................................................6-18

Summary of Contents for MXI VXI-PCI8026





































































































































Reviews: