National Instruments 9205 Calibration Procedure Download Page 11

Page: 11 / 15

National Instruments Corporation

NI 9205/9206 Calibration Procedure

Perform an external adjustment using

DAQmxMSeriesCalAdjust

(DAQmx Adjust M-Series Calibration VI), as shown in the following
table.

Save the adjustment to the EEPROM using

DAQmxCloseExtCal

(DAQmx Close External Calibration), as shown in the following table.
This function also saves the date, time, and temperature of the
adjustment to the onboard memory.

Note

If the device fails the calibration procedure, no constants are written to the

EEPROM.

Disconnect the calibrator from the device.

The device is now calibrated with respect to the external source. After
calibrating the device, verify the analog input operation by repeating the

Verification Procedure

section.

NI-DAQmx Function Call

LabVIEW Block Diagram

Call

DAQmxMSeriesCalAdjust

with the following
parameters:

calHandle

calHandle

referenceVoltage

4.0

NI-DAQmx Function Call

LabVIEW Block Diagram

Call

DAQmxCloseExtCal

with the following
parameters:

calHandle

calHandle

action

DAQmx_Val_

Action_Commit

Summary of Contents for 9205
















Search results

Summary of Contents for 9205

Reviews:

Related manuals for 9205

Brands by name

Popular brands

National Instruments 9205, Calibration Procedure

Search results

Summary of Contents for 9205

Reviews:

Related manuals for 9205

Brands by name

Popular brands