NAS E8 Installation Manual Download Page 18

E8 Swing Automatic Gate. Revision 1.1.8 –1112

18 of 19

LIMITED WARRANTY

E8 warrants the original purchaser that for a period of twelve months from the date of purchase, the
product shall be free of defects in materials and workmanship under normal use. During the warranty
period, E8 shall, as its option, repair or replace any defective product upon return of the product to its
factory, at no charge for labour and materials. Any replacement and/or repaired parts are warranted for
the remainder of the original warranty or ninety (90) days, whichever is longer. The original owner
must promptly notify E8 in writing that there is defect in material or workmanship; such written notice
shall be received in all events prior to expiration of the warranty.

International Warranty

The warranty for international customers is as the same as for any customer within Malaysia, with the
exception that E8 shall not be responsible for any customs fees, taxes, or VAT that may be due.

Warranty Procedure

To obtain service under this warranty, please return the item(s) in question to the point of purchase. All
authorized distributors and dealers have a warranty program. Anyone returning goods to E8 must first
obtain an authorization number. E8 will not accept any shipment for which prior authorization has not
been used.

Conditions to Void Warranty

This warranty applies only to defects in pairs and workmanship relating to normal use. It does not
cover:

damage incurred in shipping or handling

damage caused by disaster such as fire, flood, wind, earthquake or lightning

damage due to causes beyond the control of E8 such as excessive voltage, mechanical shock
or water damage

damage caused by unauthorized attachment, alterations, modifications, or foreign objects.

damage caused by peripherals (unless such peripherals were supplied by E8)

defects caused by failure to provide a suitable installation environment for the products

damage caused by used of the products for purpose other than those for which it was designed.

damage from improper maintenance

damage arising out of any other abuse, mishandling, and improper application of the products.

E8’s liability for failure to repair the product under this warranty after a reasonable number of attempts
will be limited to a replacement of the product, as the exclusive remedy for breach of warranty. Under
no circumstances shall E8 be liable for any special, incidental, or consequential damages based upon
breach of warranty, breach of contract, negligence, strict liability, or any other legal theory. Such
damages include, but are not limited to, loss of profits, loss of the product or any associated equipment,
cost of capital, cost of substitute or replacement equipment, facilities or services, down time,
purchaser’s time, the claims of third parties, including customers, and injury to property.

Disclaimer of Warranties

This warranty contains the entire warranty and shall be in lieu of any and all other warranties, whether
expressed or implied (including all implied warranties of merchantability or fitness for a particular
purpose). And of all other obligations or purporting to act on its behalf to modify or to change this
warranty, nor to assume for it any other warranty or liability concerning this product.
WARNING: E8 recommends the entire system be completely tested on a regular basis. However,
despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is
possible for this product to fail to perform as expected.

Out of Warranty Repairs

E8 will at this option repair or replace out-of-warranty products which are returned to its factory
according to the following conditions. Anyone returning goods to E8 must first obtain an authorization
number. E8 will not accept any shipment whatsoever for which prior authorization has not been
obtained. Products which E8 determines to be repairable will be repaired and returned. A set fee which
E8 has predetermined and which may be revised from time to time, will be charged for each unit
repaired. Products which E8 determines not repairable will be replaced by the nearest equivalent
product available at that time. The current market price for the replacement product will be charged for
each replacement unit.

Summary of Contents for E8




















Reviews: