![background image](http://html1.mh-extra.com/html/narvi/stonet-6kw/stonet-6kw_installation-and-instruction-manual_3349829019.webp)
4. USING THE HEATER
- The heater’s control switch is located at the side, at the lower part of the heater (see Fig. 5).
4.1 Overview
- The heater is switched on and off by toggling the I/O button.
- The SET button is used for setting the following
parameters: Preset timing, power-on time and temperature.
- The setting is carried out using the +/- buttons.
During set-up, an LED flashes to indicate the parameter
being set, with the respective value being displayed
on the screen.
- The settings of the power-on time and the temperature
remain in memory even after a short outage of power. After
a longer outage of power, the times are reset to their default
values. The preset timing will always be reset after use.
- The On/Off LED is illuminated red whenever the heating
elements are turned on; at all other times it is illuminated
green. During the preset time, the On/Off LED is not
illuminated.
Figure 6.
On/Off signal light
Preset timing (yellow)
Power-on
time (green)
Temp. (red)
SET
3.2 Installing the STONET heater and piling the stones
- The heater can be placed on the floor.
- When installing the heater, observe the given safe distances.
- The heater must be attached to the wall, as illustrated in Fig. 4.
- The heater has a two-part front net. The upper part can be removed to
enable easier piling of the stones in the lower part.
- Pile the stones carefully so as not to damage the exterior coating
of the heater.
- When piling the stones, make sure that the resistors do not get bent and
that the circulation of air is sufficient.
- Stones 5-10 cm in diameter are suitable for the heater.
- Pile the stones loosely. Stones that are piled too tightly may make
the resistors overheat (= shorter life span) and slow down the heating of the sauna.
- The front part of the stone space must, however, be piled as tightly as possible to cover the resistors.
- Ceramic stones cannot be used in this heater!
A STONE CONTAINER THAT IS FILLED TOO SPARSELY MAY BE A FIRE HAZARD!
BEFORE PLUGGING IN THE HEATER, INSPECT THE SAUNA ROOM!
Figure 4. Placement of the
fastening plate
Malli
Stonet 6Kw
Stonet 9Kw
80
100
X min mm
Kuva 2.
X
min. 160
225
225
240
4.8x25 6kpl
278
160
50
300
300
70
70
Tason kannatusruuvien
paikat (lattiasta 860 mm)
Model
pcs
Figure
4.1
4.2x9.5 3kpl
Figure
4.2
4.2x9.5 3kpl
4.2x9.5 3kpl
Figure
4.4
4.2x9.5 3kpl
Figure
4.3
Figure
5.
INSTALLATION ON THE WALL:
- Attach the stove to the fittings of the fastening plate that has been installed on the wall (Fig. 4.1).
- Adjust the height of the adjustable base screws: the stove should rest against the fastening plate (Fig. 4.2).
- With a special frame (available separately), the stove can also be installed in a corner.
- Screw the two fastening screws (Ø 4.2 x 9.5) into the upper frame and one screw
into the fastening plate on the wall (see Figure 4.4).
Summary of Contents for Stonet 6kW
