background image

1

W415-0612 / C / 01.25.08

INSTALLATION 

AND

OPERATION INSTRUCTIONS

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 4Y8 Canada 

 (705)721-1212 

 fax(705)722-6031

www.napoleonfireplaces.com 

 [email protected]

GD19N

NATURAL GAS

GD19P

PROPANE

- Do not store or use gasoline or other 
flammable vapors and liquids in the vicinity 
of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:
  Do not try to light any appliance.
  Do not touch any electrical switch; do  
  not use any phone in your building.
  Immediately call your gas supplier from  
  a neighbour’s phone.  Follow the gas  
 supplier’s 

instructions.

  If you cannot reach your gas supplier,  
  call the fire department.
- Installation and service must be 
performed by a qualified installer, service 
agency or the supplier.

SAFETY INFORMATION

CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: ANSI Z21.50   CSA 2.22 FOR VENTED GAS FIREPLACE.

Shown

with F

K19

If the information in these instructions are 
not followed exactly, a fire or explosion 
may result causing property damage, 
personal injury or loss of life.

!

WARNING

INSTALLER:  LEAVE THIS MANUAL WTIH THE APPLIANCE.

CONSUMER:  RETAIN THIS MANUAL FOR FUTURE REFERENCE.

$10.00

Summary of Contents for Vittoria GD19N





































Reviews: