Napoleon PTH55PSS-1 User Installation And Operation Manual Download Page 9 | Manualshive

Page: 9 / 12

Napoleon PTH55PSS-1 User Installation And Operation Manual Download Page 9

8

If you detect bubbles, there is a leak. Close cylinder valve completely. Retighten the

leaking connection and repeat leak test process.

If the leak cannot repaired permanently, close cylinder valve completely and contact

the customer service department at 1-866-539-2039 or a qualified gas technician.

A SAFE LOCATION FOR THE HEATER

CAUTION

When objects are left under a heater in operation, they will be subject to radiant heat

and might be damaged.

● The principal application of this heater is to provide heat to pool and
spa areas, terraces, work areas, etc.

This heater is approved for outdoor use only.

●    Provide fresh air ventilation at all times
●    Respect minimum clearances to combustibles as shown in figure 11 below.
●    Install heater on a leveled, solid and stable ground.
●    Do not install in an explosive environment.    Keep away from areas from where gas,
      vapors or flammable liquids are stored or used.
●    In case of high winds, shut-off completely the heater and the cylinder gas valve.
      Remove reflector dome.
●    Do not move the heater when hot.

CLEARANCES FROM COMBUSTIBLES

Respect clearances as shown:

-

Sides of reflector : 60 cm

-

Above reflector : 45 cm

«
...
7
8
9
10
11
...
»

Summary of Contents for PTH55PSS-1













Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands