background image

 

25

www.napoleongrills.com

ATTENTION!

 Lors du déballage et de l’assemblage, nous vous conseillons de porter des gants 

de travail et des lunettes de sécurité pour votre protection. Malgré tous nos efforts pour assurer que 

l’assemblage soit aussi sécuritaire et sans problème que possible, il se peut que les bords et les coins des 

pièces usinées en acier soient coupants et qu’ils causent des coupures si les pièces ne sont pas manipulées 

correctement.  

CAUTION!

 During unpacking and assembly we recommended you wear work gloves and safety glasses 

for your protection.  Although we make every effort to make the assembly process as problem free and 

safe as possible, it is characteristic of fabricated steel parts that the edges and corners might be sharp and 

could cause cuts if handled incorrectly.

Getting Started

1.  Remove all of the parts from the carton.  Use the parts list to ensure all necessary parts are included.   
2.  Do not destroy packaging until the patio torch has been fully assembled and operates to your satisfaction.
3.  Assemble the patio torch where it is to be used, lay down cardboard or a towel to protect parts from 

being lost or damaged while assembling.

4.  Most stainless steel parts are supplied with a protective plastic coating that must be removed prior to 

using the patio torch.

5.  Follow all instructions in the order that they are laid out in this manual.

If you have any questions about assembly or patio torch operation, or if there are damaged or missing 

parts please call our Customer Care Department at 1-866-820-8686 between 9 AM and 5 PM (Eastern Standard 

Time).

Philips 

screwdriver

3/4 (19mm) 

Wrench

Pour Commencer

1.  Retirez tous les pièces du carton d’emballage.   Servez-vous de la liste de pièces pour vous assurer que 

toutes les pièces nécessaires sont incluses.   

2.  Ne détruisez pas l’emballage jusqu’à ce que le torche-patio ait été complètement assemblé et qu’il fonctionne 

à votre satisfaction.

3.  Assemblez le torche-patio là où il sera utilisé et posez un carton ou une serviette afin d’éviter de perdre ou 

d’endommager les pièces lors de l’assemblage.

4.  La plupart des pièces en acier inoxydable possèdent un revêtement de plastique protecteur qui doit être 

enlevé avant d’utiliser le torche-patio. 

5.  Suivez toutes les instructions dans l’ordre donné dans ce manuel.

Si vous avez des questions à propos de l’assemblage ou du fonctionnement du gril, ou si des pièces sont 

manquantes ou endommagées, veuillez appeler notre département du Service aux Consommateurs au 

1-866-820-8686 entre 9 h et 17 h (heure normale de l’Est).

Tournevis phillips

OUTILS REQUIS POUR L’ASSEMBLAGE (outils non inclus)

TOOLS REQUIRED FOR ASSEMBLY (tools not included)

Clé ¾ po (19 mm)

Summary of Contents for PTH31GT
























Reviews: