background image

 

7

www.napoleongrills.com

Lighting Instructions

WARNING!

 Never use the torch while it is raining, the glass tube could crack or break causing serious 

injury.

WARNING!

 Ensure burner controls are in the off position. Slowly turn on the gas supply valve.

1. Turn burner control to ‘LIGHT’ 

position.

2. Press and hold igniter button until 

pilot lights, or light by match.

(check for pilot flame through glass 

tube)

3. Once pilot is lit, keep control knob 

depressed for 15 seconds and then 

turn control knob to ‘LOW’.

4. If ignition is not immediate, turn 

burner control off.  Wait 5 minutes.

Repeat.

5.  For maximum heat turn control 

knob to ‘HIGH’

6.  To turn off the patio torch, turn the 

control knob to the ‘OFF’ 

 position and then turn the gas supply 

off at the source.

WARNING!

 The propane cylinder is equipped with an excess flow device.  Unless burners are turned 

off, prior to turning the cylinder on, only small flames and low heat will be achievable.

WARNING!

 If lighting the unit with a match, clip the match into the supplied lighting rod.  

Hold the lit match through the hole in the bottom or front of the control box while turning the 

burner valve to high.

Lighting Holes

Summary of Contents for PTH31GT
























Reviews: