5
W415-0580 / B / 03.12.08
GENERAL INSTRUCTIONS
GENERAL INFORMATION
This gas fireplace should be installed and serviced by a qualified installer to conform with local codes. Installation practices vary from
region to region and it is important to know the specifics that apply to your area,
for example: in Massachusetts State:
• The fireplace damper must be removed or welded in the open position prior to installation of a fireplace insert or gas log.
• The appliance off valve must be a “T” handle gas cock.
• The flexible connector must not be longer than 36 inches.
• A Carbon Monoxide detector is required in all rooms containing gas fired appliances.
• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed combustion product.
• WARNING: This product must be installed by a licensed plumber or gas fitter when installed within the commonwealth of Massachu-
setts.
In absence of local codes, install to the current CAN/CGA -B149 Installation Code in Canada or to the National Fuel Gas Code, ANSI
Z223.1, and NFPA 54 in the United States. Suitable for mobile home installation if installed in accordance with the current standard
CAN/CSA Z240MH Series, for gas equipped mobile homes, in Canada or ANSI Z223.1 and NFPA 54 in the United States.
The fireplace and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that
system at test pressures in excess of 1/2 psig (3.5 kPa). The fireplace must be isolated from the gas supply piping system by closing its
individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2
psig (3.5 kPa).
When the fireplace is installed directly on carpeting, vinyl tile or other combustible material other than wood flooring, the fireplace shall be
installed on a metal or wood panel extending the full width and depth.
The optional heat circulating blower is supplied with a cord. If installed, the junction box must be electrically connected and grounded in
accordance with local codes. In the absence of local codes, use the current CSA C22.1 Canadian electrical code in Canada or the
ANSI/NFPA 70 national electrical code in the United States.
Purge all gas lines with the glass door of the fireplace open. Assure that a continuous gas flow is at the burner before closing the door.
Under extreme vent configurations, allow several minutes (5-15) for the flame to stabilize after ignition.
Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing and operating the fireplace.
Never obstruct the front opening of the fireplace.
Objects placed in front of the fireplace must be kept a minimum of 48” from the front face of the unit.
It is recommended that the walls of the fireplace enclosure be finished. This would ensure that clearance to combustibles is maintained
with the cavity.
Non-combustible finishing material (i.e.. cement board, brick, stone, tile) must be used to finish the front of the unit.
FOR YOUR SATISFACTION, THIS FIREPLACE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND QUALITY!
Maximum input is
50,000 BTU/hr for both natural gas and propane. When the fi replace is installed at elevations above 4,500ft, and in the absence of specifi c
recommendations from the local authority having jurisdiction, the certifi ed high altitude input rating shall be reduced at the rate of 4% for
each additional 1,000ft. Maximum output for natural gas is 33,540 BTU/hr at an effi ciency of 63%; and 34,000 BTU/hr for propane at an
effi ciency of 61%. Minimum inlet gas supply pressure is 4.5“ water column for natural gas and 11“ water column for propane. Maximum inlet
gas pressure is 7“ water column for natural gas and 13“ water column for propane. Manifold pressure under fl ow conditions is 3.5 inches
water column for natural gas and 10 inches water column for propane.
This fi replace is approved for bathroom, bedroom and bed-sitting room installations and is certifi ed for mobile home installation. The natural
gas model can only be installed in a mobile home that is permanently positioned on its site and fueled with natural gas.
This fireplace is only for use with the type of gas indicated on the rating plate. This
fireplace is not convertible for use with other gases, unless a certified kit is used.
No external electricity (110 volts or 24 volts) is required for the gas system operation.
Expansion / contraction noises during heating up and cooling down cycles are normal
and are to be expected. Change in flame appearance from “HI” to “LO” is more evident
in natural gas than in propane.
CARE OF GLASS
We Suggest that our gas
hearth products be installed
and serviced by profession-
als who are certified in the
U.S. by the National
Fireplace Institute (NFI) as
NFI Gas Specialists.
Do not use abrasive cleaners to clean plated parts. Buff lightly with a
clean dry cloth. Refer to “REPLACEMENT PARTS” to find out what
this product is equipped with and the thickness of the glass.
Use only replacement glass available from your Napoleon dealer.
DO
NOT SUBSTITUTE MATERIALS.
Clean the glass after the first 10
hours of operation with a recommended gas fireplace glass cleaner.
Thereafter clean as required.
DO NOT CLEAN GLASS WHEN HOT!
If the glass is not kept clean
permanent discoloration and / or blemishes may result.