background image

7

W415-0779 / A / 04.27.10

2.4  RATING PLATE INFORMATION

INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to 
the model, venting and gas type of the appliance.

For rating plate location, see “INSTALLATION OVERVIEW” section.

CERTIFIED UNDER / HOMOLOGUE SELON LES NORMES: CSA 2.33-2009, ANSI Z21.88-2009 VENTED GAS FIREPLACE HEATER / FOYER DE CHAUFFAGE AU GAZ AVEC EVACUATION.

CERTIFIED FOR

CERTIFIEE POUR

CANADA         USA

AND

ET

WOLF STEEL LTD, BARRIE, ON, CANADA

MADE IN CANADA / FABRIQUE AU CANADA

SERIAL NUMBER/NO. DE SERIE: 

BGD42CF

W385-0343 / E

MANIFOLD PRESSURE: 3.5" WATER COLUMN

PRESSION AU COLLECTEUR: 3.5" D'UNE COLONNE D'EAU

MINIMUM SUPPLY PRESSURE: 4.5" WATER COLUMN

PRESSION D'ALIMENTATION MINIMALE: 4.5" D'UNE COLONNE D'EAU

MAXIMUM SUPPLY PRESSURE: 7.0" WATER COLUMN

PRESSION D'ALIMENTATION MAXIMALE: 7.0" D'UNE COLONNE D'EAU

MANIFOLD PRESSURE: 10" WATER COLUMN

PRESSION AU COLLECTEUR: 10" D'UNE COLONNE D'EAU

MINIMUM SUPPLY PRESSURE: 11" WATER COLUMN

PRESSION D'ALIMENTATION MINIMALE: 11" D'UNE COLONNE D'EAU

MAXIMUM SUPPLY PRESSURE: 13" WATER COLUMN

PRESSION D'ALIMENTATION MAXIMALE: 13" D'UNE COLONNE D'EAU

ALTITUDE / ELEVATION 

INPUT / ALIMENTATION

REDUCED INPUT / ALIMENTATION REDUITE

ORIFICE / INJECTEUR

MODEL

BGD42CFN                BCDV42CFN

0-4500 FT (0-1370M)

24,000 BTU/H

17,000 BTU/H

#43

MODEL

BGD42CFP                BCDV42CFP

0-4500FT (0-1370M)

24,000 BTU/H

18,000 BTU/H

#54

DIRECT VENT GAS FIREPLACE. APPROVED FOR BEDROOM, BATHROOM AND BED-SITTING ROOM INSTALLA-

TION. SUITABLE FOR MOBILE HOME INSTALLATION IF INSTALLED IN ACCORDANCE WITH THE CURRENT 

STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES, IN CANADA OR IN THE UNITED STATES 

THE MANUFACTURED HOME CONTRUCTION AND SAFETY STANDARD, TITLE  24 CFR, PART 3280. WHEN THIS US 

STANDARD IS NOT APPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME 

INSTALLATIONS, SITES AND COMMUNITIES, ANSI / NFPA 501A. WHEN INSTALLED WITH SCREEN KIT GD-565KT, 

THE FIREPLACE COMPLIES WITH CGA CERTIFICATION REQUIREMENT CR95-006.

FOYER A GAZ VENTILE DIRECT. HOMOLOGUE POUR INSTALLATION DANS UNE CHAMBRE A COUCHER, UNE SALLE 
DE BAIN ET UN STUDIO. APPROPRIE POUR INSTALLATION DANS UNE MAISON MOBILE SI SON INSTALLATION 
CONFORME AUX EXIGENCES DE LA NORME CAN/CSA Z240MH SERIE DE MAISONS MOBILES EQUIPEES AU GAZ, EN 
VIGUEUR AU CANADA OU AUX ETATS-UNIS DE LA NORME DE  SECURITE ET DE CONSTRUCTION DE MAISONS 
MANUFACTUREES, TITRE 24 CFR, SECTION 3280. DANS LE CAS OU CETTE NORME D'ETATS-UNIS NE PEUT ETRE 
APPLIQUEE, SE REFERER A LA NORME RELATIVE AU CRITERE DE MESURES DE SECURITE CONTRE L'INCENDIE 
POUR LES INSTALLATIONS DANS LES MAISONS MANUFACTURES, LES SITES ET LES COMMUNAUTES, ANSI/NFPA 
501A. LORSQU'IL   EST INSTALLE AVEC LA TROUSSE POUR ECRAN GD-565KT, LE FOYER EST CONFORME A LA NORME 

DE CERTIFICATION DE L'ACG CR95-006.

NOT FOR USE WITH SOLID FUEL. FOR USE WITH GLASS DOORS CERTIFIED 
WITH THIS UNIT ONLY.

UN COMBUSTIBLE SOLIDE NE DOIT PAS ETRE UTILISE AVEC CET APPAR-

EIL. UTILISER AVEC LES PORTES VITREES HOMOLOGUEES SEULEMENT 

AVEC CETTE UNITE.

AVERTISSEMENT: CE FOYER UTILISE ET REQUIERT UN THERMOCOUPLE À ACTION RAPIDE. REMPLACEZ UNIQUEMENT AVEC 

UN THERMOCOUPLE À ACTION RAPIDE DE WOLF STEEL LTÉE. 

N'AJOUTEZ PAS A CET APPAREIL AUCUN MATERIAU DEVANT ENTRER EN CONTACT AVEC LES FLAMMES AUTRE QUE CELUI 

QUI EST FOURNI AVEC CET APPAREIL PAR LE FABRICANT.  

THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE WOLF STEEL VENT KITS.  SEE OWNERS INSTALLATION MANUAL 
FOR VENTING SPECIFICS. PROPER REINSTALLATION AND RESEALING IS NECESSARY AFTER SERVICING THE VENT-AIR 

INTAKE SYSTEM.

L'APPAREIL DOIT EVACUER SES GAZ EN UTILISANT L'ENSEMBLE D'EVACUATION PROPRE A WOLF STEEL. REFERER AU 
MANUEL D'INSTALLATION DE PROPRIETAIRE POUR L'EVACUATION PRECISE.  IL EST IMPORTANT DE BIEN REINSTALLER ET 
RESCELLER L'EVENT APRES AVOIR ASSURE LE MAINTIEN DU SYSTEME DE PRISE D'AIR.  ELECTRICAL RATING / CLASSIFICA-

TION: 115V 0.82AMP, 60HZ OPTIONAL FAN KIT / ENSEMBLE DE VENTILATEUR FACULTATIF: GZ550-KT, GD65

WARNING: THIS FIREPLACE USES AND REQUIRES A FAST ACTING THERMOCOUPLE.  REPLACE ONLY WITH A FAST ACTING 
THERMOCOUPLE SUPPLIED BY WOLF STEEL LTD.  DO NOT ADD ANY MATERIAL TO THE APPLIANCE, WHICH WILL COME IN 
CONTACT WITH THE FLAMES, OTHER THAN THAT SUPPLIED BY THE MANUFACTURER WITH THE APPLIANCE.

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS / DEGAGEMENTS MINIMAUX DES MATERIAUX COMBUSTIBLES:
TOP/ DESSUS   

0

RECESSED DEPTH / PROFONDEUR D'ENCASTRE 

25" 

FLOOR / PLANCHER 

VENT SIDES / COTES DE L'EVENT  

  

1"

SIDES / COTES  

0

VENT TOP / EVENT SUPERIEUR 

2"

BACK / ARRIERE 

0

VENT BOTTOM / EVENT INFERIEUR 

  

1"

MANTLE / MANTEAU 

12" *

* MAXIMUM HORIZONTAL EXTENSION / L'EXTENSION HORIZONTALE MAXIMALE:   

 

2".

TOP, SIDES & BACK: PER STAND OFF SPACES FOR FRAMING MATERIALS. FOR FINISHING MATERIALS SEE OWNERS MANUAL. 
SEE INSTRUCTION MANUAL FOR GREATER EXTENSIONS. REFERER AU MANUEL D'INSTRUCTION POUR DES EXTENSIONS 

PLUS GRANDES.  SEE OWNER'S INSTRUCTION MANUAL FOR MINIMUM AND MAXIMUM VENT LENGTHS.  REFERER AU 

MANUEL D'INSTALLATION DE PROPRIETAIRE POUR LES LONGUEURS L'EVACUATION MINIMALE ET MINIMALE.

REFERENCE # W/N 15539

Summary of Contents for BGD42CFN

















































Reviews: