791-7135 3 03/04/16
SETUP
PLEASE REFER TO THE EXPLODED VIEW DRAWING IN THIS MANUAL IN ORDER TO IDENTIFY PARTS.
1. Attach the fuel tank adapter saddle #3 to the transmission jack hydraulic unit ram using #9 bolt.
2. Attach fuel tank adapter #1 to saddle #3 using 2 each #6 bolts, #7 washers, and #8 wing nuts. The bolts should be inserted on opposite
ends of the saddle. Make sure the fuel tank adapter is fastened securely to the saddle.
3. Install the four padded supports #2 on the fuel tank adapter saddle #1 as shown in the exploded view drawing and secure them with the
wing bolts #4.
OPERATING INSTRUCTIONS
This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
1. Prepare the fuel tank for removal according to the appropriate vehicle service manual instructions and procedure. Drain the fuel tank into a
grounded storage container.
2. Pump the jack up so the fuel tank saddle adapter is close but not touching the vehicle's fuel tank. Adjust the four padded supports #2 to fit
the fuel tank configuration, and then center and balance the tank on the saddle adapter.
3. Raise the jack so the saddle adapter makes contact with the fuel tank and make final adjustments. Make sure the wing bolts #4 are tight.
4. Secure the fuel tank to the saddle adapter by wrapping the two tie-down straps completely around the tank and saddle. Insert the tie-
down straps through their buckles and pull tight.
5. Make sure the tank is free to be lowered all the way down and there are no obstructions. The jack must be lowered all the way before the
tank can be transported.
PREVENTATIVE MAINTENANCE
This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
1. Always store the adapter in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive dust, or any
other harmful elements. The adapter must be cleaned of water, snow, sand, grit, oil, grease or other foreign matter before using.
2. Every adapter owner is responsible for keeping the adapter labels clean and readable. Use a mild soap solution to wash external surfaces
of the adapter.
3. Do not attempt to make any repairs unless you are a qualified repair person that is familiar with this equipment. Do not use the adapter if it
is damaged, cracked, broken, or missing parts. Take it out of service until replaced or properly repaired by an authorized service center.
INSPECTION
Visual inspection should be made before each use of the adapter, checking for damaged, loose or missing parts. Each adapter must be
inspected by a manufacturer’s repair facility immediately if subjected to an abnormal load or shock. Any adapter which appears to be
damaged in any way, is found to be badly worn, or operates abnormally MUST BE REMOVED FROM SERVICE until necessary repairs are
made by a manufacturer’s authorized repair facility. It is recommended that an annual inspection of the adapter be made by a manufacturer’s
authorized repair facility and that any defective parts, decals or warning labels be replaced with manufacturer’s specified parts. A list of
authorized repair facilities is available from the manufacturer.
PROPER STORAGE
It is recommended that the adapter be stored in a dry location.
OWNER/USER RESPONSIBILITY
The owner and/or user must have an understanding of the manufacturer’s operating instructions and warnings before using this adapter.
Personnel involved in the use and operation of equipment shall be careful, competent, trained, and qualified in the safe operation of the
equipment and its proper use when servicing motor vehicles and their components. Warning information should be emphasized and
understood. If the operator is not fluent in English, the manufacturer’s instructions and warning shall be read to and discussed with the
operator in the operator’s native language by the purchaser/owner, making sure that the operator comprehends its contents. Owner and/or
user must study and maintain for future reference the manufacturers’ instructions. Owner and/or user is responsible for keeping all warning
labels and instruction manuals legible and intact. Replacement labels and literature are available from the manufacturer.
OPERATING MANUAL & PARTS LIST FOR 791-7135
WARRANTY
Please contact your local NAPA Auto Parts Store for details on warranty.
