NanoRFE VNA6000 User Manual Download Page 2 | Manualshive

Page: 2 / 29

NanoRFE VNA6000 User Manual Download Page 2

Table of Contents

Table of Contents

1 - Introduction

Safety information ..................................................................................................................... 3

Basic concepts ........................................................................................................................... 3
First steps .................................................................................................................................. 4

2 - User interface

Main screen ................................................................................................................................ 5
Menu screen ............................................................................................................................... 7
Keypad screen ............................................................................................................................ 8

Device settings .......................................................................................................................... 9

3 - Performing measurements

Setting the measurement frequency range ..............................................................................12

Calibration ................................................................................................................................ 13
Trace display ............................................................................................................................ 15

Markers .................................................................................................................................... 17
Time domain operation ............................................................................................................ 18
Recall calibration and settings .................................................................................................22

4 - VNA View Software

User interface .......................................................................................................................... 24
Connecting to the device ......................................................................................................... 25
Setting sweep range and parameters ......................................................................................26
Calibration ................................................................................................................................ 27
Firmware Update ..................................................................................................................... 29

VNA6000 User Manual 2022/08

2

«
1
2
3
4
...
»

Summary of Contents for VNA6000






























Reviews:

No comments