Page 19 of 44
Copyright © NAGRAVISION S.A. 2005-2009
April 28, 2009
InDev manage
NAME: NAGRA
TYPE:
EXT-MIC
GAIN: +0dB
BST: +19dB
PWR: ON
FLT: 100-20kHz
Manager input device
OK
NAGRA
OK
InDev manage
NAME: NAGRA
TYPE: EXT-MIC
GAIN: +
0dB
BST: +19dB
PWR: ON
FLT: 100-20kHz
Manager input device
OK
NAGRA
OK
InDev manage
NAME: NAGRA
TYPE: EXT-MIC
GAIN: +0dB
BST: +
19dB
PWR: ON
FLT: 100-20kHz
Manager input device
OK
NAGRA
OK
InDev manage
NAME: NAGRA
TYPE: EXT-MIC
GAIN: +0dB
BST: +19dB
PWR:
ON
FLT: 100-20kHz
Manager input device
OK
NAGRA
OK
InDev manage
NAME: NAGRA
TYPE: EXT-MIC
GAIN: +0dB
BST: +19dB
PWR: ON
FLT:
100-20kHz
Manager input device
OK
NAGRA
OK
9.5.2 Input device type manager
This sub-menu gives the selection of the input that will be used for recording. To change the input
type, go to “Manager input device” and press “
OK
” followed by the “
DOWN
” key. Then “
TYPE
” will be
highlighted.
Five selections are possible: Internal mike, External mike, Line, Line Lo and Line Hi
input.
By using the “
LEFT
” or “
RIGHT
” keys, select the corresponding input type and press
“
DOWN
” to go to the next step.
9.5.3 Input gain manager
To change the input gain of an input device type, select the corresponding name and press “
OK
”
followed by the “
DOWN
” key twice.
The “
INT-MIC
” gain can be pre-adjusted from 0 dB to 28 dB in steps of 2 dB. The
“
EXT-MIC
” can be adjusted from 0 dB to 24 dB in steps of 3 dB. The “
LINE
” input
can be adjusted from 0 dB to 24 dB in steps of 3 dB. To modify the value, use the
“
LEFT
” or “
RIGHT
” keys. Once the corresponding value is set, press “
DOWN
” to go
to the next step.
9.5.4 Input boost manager
Only for the “
EXT-MIC
” an additional boost can be added to the previous gain setting. To change the
input boost, select the corresponding name and press “
OK
” followed by the “DOWN” key three times.
By pressing the “
LEFT
” or “
RIGHT
” keys, the “
BST
” can be set to +19 dB or +34
dB. Once the corresponding setting is made, press “
DOWN
” to go to the next step.
9.5.5 Input power manager
Power can only be turned on for the “
EXT- MIC
”. To select the input power, select the corresponding
name and press the “
OK
” followed by the “
DOWN
” key four times.
The power available for Electret mikes is 3V dc. By pressing the “
LEFT
” or “
RIGHT
”
keys, the “
PWR
” can be turned ON or OFF, then press “
DOWN
” to go to the next
step.
9.5.6 Input filter manager
A filter can be selected for the “
EXT-MIC
”. To select the input filter, select the corresponding name
and press “
OK
” followed by the “
DOWN
” key five times.
Two possibilities are available: Flat (20-20kHz) or Low cut (100-20kHz). By
pressing the “
LEFT
” or “
RIGHT
” keys, the “
FLT
” can be
turned ON or OFF. Press
“
OK
” to validate.