1 STANDBY
BUTTON
t
Press this button to switch ON the T 187 from standby mode. The
Standby LED indicator will turn from amber to blue and illuminate
the VFD. Pressing the STANDBY button again turns the unit back to
standby mode.
t
The T 187 can also be switched ON from standby mode by pressing
any of the front panel buttons.
NOTE
The rear panel POWER switch must be in the ON position for the Standby
button to activate.
2 STANDBY
LED
t
This indicator will light up amber when the T 187 is at standby
mode.
t
When the T 187 is powered up from standby mode, this indicator
will illuminate blue.
t
If a Zone (Zone 2, Zone 3 or Zone 4) is ON and STANDBY button
is pressed to switch the T 187 to standby mode, the VFD will be
extinguished but the STANDBY LED remains illuminated blue.
This indicates a Zone (Zone 2, Zone 3 or Zone 4) is still active. The
corresponding active Zone icon(s) will also remain displayed in the VFD.
t
In order to completely shut down the T 187 with Zone 2, Zone 3
and/or Zone 4 still ON, press and hold STANDBY button until the
STANDBY LED turns amber.
3 NAVIGATION and ENTER BUTTONS
The navigation ([
d/f/a/s
]) and [ENTER] buttons have various
applications specific to given modes. The middle round button is
designated as [ENTER] button; this is normally pressed to complete a
selection, procedure, sequence or other applicable functions.
AM/FM mode
Toggle [ENTER] button to switch between “Tune” and “Preset” mode.
Select “Tune” mode.
t
Pressing momentarily the [
a/s
] button will manually scan the AM
or FM band.
t
Press and hold [
a/s
] for more than 2 seconds to search up or
down; the T 187’s tuner will stop at the next sufficiently strong signal
it encounters.
t
Note that this function “wraps” - that is, it will continue to search
from one end of the AM or FM band to the other until it stops at a
strong signal.
Toggle [ENTER] button to switch between “Tune” and “Preset” mode.
Select “Preset” mode.
t
Use [
d/f
] to step up or down AM/FM Presets. Unused presets are
skipped over. Note that Presets must have been previously stored.
Refer also to the item about STORING PRESETS (AM/FM/XM/DAB) at the
LISTENING TO AM/FM RADIO section of the OPERATION page.
XM mode (120V version model only)
t
Use the front panel [
d/f
] and [ENTER] buttons in combination
with the [MENU] button to select through applicable XM menu
options.
DAB mode (230V version model only)
t
Use front panel [
a/s
] and [ENTER] buttons in combination with
[MENU] button to select through applicable DAB menu options.
4 REMOTE
SENSOR
t
Point the HTR 8 remote control at the remote sensor and press the
buttons.
t
Do not expose the remote sensor of the T 187 to a strong light
source such as direct sunlight or illumination. If you do so, you may
not be able to operate the T 187 with the remote control.
Distance:
About 23ft (7m) from the front of the remote sensor.
Angle:
About 30
o
in each direction of the front of the remote sensor.
IDENTIFICATION OF CONTROLS
FRONT PANEL
NAD T187
© NAD T 187
AV Surround Sound Preamp Processor
T 187
a
SOURCE
s
VOLUME
MEMORY
s
a
d
f
INFO
DELETE
AM/FM/DB
TUNER MODE
LISTEN MODE
TONE
TONE DEFEAT FRONT INPUT/MP
4
5
6
7
17
A
B
C
E
D
12
13
14
15
16
11
1
2
3
18
10
9
8
6
ENGLISH
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
Р
У
С
СКИЙ
