background image

North American Clutch & Driveline

Rockford, Illinois

Phone: (800) 383-9204

            (815) 282-7960

Fax       (815) 282-9160

www.naclutch.com

3

Parts Shipment

Furnish the complete shipping information and postal address.  All parts shipments made 
from the factory will be FOB factory location, USA.  State specifically whether the parts 
are to be shipped by freight, express, etc.  If shipping instructions are not specified, the 
equipment will be shipped the best way, considering time and expense.  NACD will not 
be responsible for any charges incurred by this procedure.

NACD, having stipulated the bill of material number on the unit’s nameplate, absolves 
itself of any responsibility resulting from any external, internal or installation changes 
made in the field without the express written approval of NACD.  All returned parts, new 
or old, emanating from any of the above-stated changes will not be accepted for credit.  
Furthermore, any equipment which has been subjected to such changes will not be cov-
ered by a NACD warranty.

Preventative Maintenance/Troubleshooting

Frequent reference to the information provided in this manual regarding daily operation 
and limitations of this equipment will assist in obtaining trouble-free operation.  Sched-
ules are provided for the recommended maintenance of the equipment and, if observed, 
minimal repairs (aside from normal wear) will result.

Lifting Bolt Holes

Most NACD products have provisions for attaching lifting bolts.  The holes provided are 
always of adequate size and number to safely lift the NACD product.

These lifting points must not be used to lift the complete power unit.  Lifting exces-
sive loads at these points could cause failure at the lift point (or points) and result 
in damage or personal injury.

Select lifting eyebolts to obtain maximum thread engagement with bolt shoulder tight 
against housing.  Bolts should be near but should not contact bottom of bolt hole.

Summary of Contents for 11.5

































Reviews: