background image

Model 710 Swing Door System

NABCO

ENTRANCES INC

877-622-2694

www.nabcoentrances.com

- 14 -

Back

check

M

ain

 s

pe

ed

Full

Open

Closed

Latch

Check

DN0035

The GT 710 has two magnetic switches that control the back check location
and monitors the door closed position.  The back check magnet must be installed 
before the unit is tested.  It signals the motor to slow down so the door does not 
slam open.

The door closed magnet is optional.  It is used to signal the control board that the 
door is closed.  It is used in applications where a sensor is on the swing side of 
the door and wired into the safety with lockout circuit.  The switches are closed 
by magnets installed by the installer onto the main sprocket gear.

The magnets are not inside the header!

Locate the ¼-inch square and 1-inch long magnets in the parts bag.  To position 
the magnets, use the appropriate configuration from 

Figures 10 through 13

.

Start with the door in the closed position.  Place a magnet under the door closed 
switch with the white side up.  This magnet will deactivate the optional presence 
detector as the door begins to open.

Move the door to the 45º position.  Place a magnet under the back check switch 
with the white side up.  The magnet is positioned to move under the switch when 
the door is opened to 45º.  Use the appropriate configuration from 

Figures 10

through 13

.  This magnet will command the motor to reduce the door speed to 

the setting of the back check potentiometer.  Improper placement of this magnet 
will cause the door to slam into the door stop.

After

power is applied to the unit and the position of the magnets is “fine tuned” 

to make the door functional, the magnets should be epoxied in place following the 
instructions on the epoxy packaging.

Figure 9 – Stages of Door Travel

Setting Back Check and
Door Closed Switches

Summary of Contents for 710























Reviews: