+12v
GND
Video in
1
2
3
4
ON
1
2
3
4
5
6
7
8
ON
Microphone
DC24V
±
1 (from central unit)
0.4W (Min.), 14W (Max)
8 Wires
Full duplex
2 doorbell melodies , 2 phone melodies and 1 Alarm melody
ABS
7” Color LCD
Calling time : 30 sec, Talking Time : 60 sec
235 (Heigth) x 125 (Width) x 28 (depth) mm
Audio - Brightness / Colour
-20°C - +40°C
IP20
TECHNICAL CHARACTERISTICS
Operation voltage
Power consumption
Connection
Audio communication
Calling Melody
Material Content
Monitor
Monitor operating time
Dimensions
Settings
Operating temperature
Protection class
Functions
Communication with panel
Panel display
CCTV display
Communication with security
Door opener control
Communication with doorkeeper
MONITOR FUNCTIONS
NVM-800MC MONITOR
Monitor screen
FIGURE -7.1
Monitor On-Off
Door Open Button
Calling doorkeeper
Panel Display
CCTV Display
Calling Security
Ending resistance setting
I. ID Switch
Speaker
FIGURE -7.2
Brightness
settings
Ring level
settings
Colour
settings
Calling Security :
It is used to call security. After the button
is pressed and while the monitor is “ON” position If button is
pressed security phone
will ring. If the either side does not end the phone call, after 60
seconds system automatically ends the call. If there is more
than one security in the system, in order to call first security
press the button once. To call second security press the
button twice. If the same process is repeated , other securities
are called. Maximum duration of pressing buttons should be 1
sn in these combinations.
Ring volume tuning:
Allows you to adjust ring volume tone.
Colour tuning:
Allows you to adjust colour for LCD monitors.
Brightness tuning:
Allows you to adjust brightness.
External video Input:
Additional camera connection shown in
figure-7.2. Indoor Camera can be monitored by when
somebody press door bell button or can be monitored by CCTV
button as shown in figure-7.1. In case of using external video
input , 2nd group DIP switch must be set by 4th digit UP
position (”1”) as shown in figure-7.2. If there is no external
video input this switch must be DOWN position (”0”).
75ohm video termination switch:
This switch must be ON
position as shown in figure-7.2.
Note:
If system is installed with an alarm detector, all the
monitors will emerge householders by alarm event for 1 minute.
2. ID Switch
External video input
Screen:
Monitor, colourful LCD
Audio Button:
Allows handsfree audio output and input with
speaker and microphone
Door Open Button
:
It is used to open entrance door.
Stairways lighting / Doorkeeper button :
The sign is used
for stairways lighting both when monitor is at “OFF” position
or when monitor is at busy position.
After the button is
pressed and while the monitor is “ON” position If button is
pressed doorkeeper phone will ring. If the either side does not
end the phone call, after 60 seconds system automatically ends
the call. If there is more than one security in the system, in order
to call first doorkeeper press the button once. To call second
doorkeeper press the button twice. If the same process is
repeated , other doorkeepers are called. Maximum duration of
pressing buttons should be 1 sn in these combinations.
Panel Display :
When it is pressed to panel display button,
monitor gives the view of camera on the panel for 30 seconds.
If there is more than one panel on the system, when it is pressed
to button again during monitor have view of first panel, the
monitor gives the view of second panel if there is not another
panel, display turns off.
CCTV Display
:
If there is a CCTV camera on the system,
it gives the view of CCTV camera on the monitor for 30 seconds.
Before time is over when it is pressed again displays the other
CCTV camera’s view. If not, display turns off.
ID settings:
You can make ID giving at NVM-800MC monitor by two seperate ID switches ( DIP SWITCHES). The first ID Switch and 2nd
ID switch is shown at Figure-7.2. First ID switch represents main ID number ( Flat number) and second ID switch indicates slave
montiors’ ID number ( if there are more than 1 monitor in same flat). If there will be used only one monitor in the flat then
the 2nd ID number must be “1” position.
Example: ID settings for 3 flats;
1st Monitor :
1. ID = 1, 2. ID = 1
2nd Monitor :
1. ID = 2, 2. ID = 1
3rd Monitor :
1. ID = 3, 2. ID = 1
Example: ID settings for 3 flats with 1 slave monitor for last monitor:
1st Monitor :
1. ID = 1, 2. ID = 1
2nd Monitor :
1. ID = 2, 2. ID = 1
3rd Monitor / master :
1. ID = 3, 2. ID = 1
3rd Monitor slave :
1. ID = 3, 2. ID = 2
36
Summary of Contents for GK-04-8
Page 2: ......
Page 50: ...45 FARKLI BA LANTI UYGULAMALARI BÖLÜM 10 ...
Page 68: ......
Page 116: ...45 DIFFERENT WIRING COMBINATIONS SECTION 10 ...
