N-Tron 7018 Technical Instructions Download Page 27 | Manualshive

Page: 27 / 33

background image

Revision 2010-11-15

Page 27 of 33

Configuring DHCP Servers (2)

Download the DHCP configuration from DHCP Server (1) using TFTP. See section
Firmware/Config – TFTP.

Disable DHCP Server on the second server.

Upload this file to the second DHCP Server. See section Firmware/Config – TFTP.

If TFTP is not available repeat the process from section:

Configuring one of the DHCP

Servers (1)

, on the second Server.

Enable the DHCP Server on the second server.

Verify that the Profiles and Mappings on both servers are the same.

Third Step: Configure the DHCP Relay Agent

Enable the Relay Agent.

Define the Option 82 data for the Clients.

«
...
25
26
27
28
29
...
»

Summary of Contents for 7018


































Reviews:

No comments

Related manuals for 7018

3C410012A - OfficeConnect Remote 531 Access...

Brand: 3Com Pages: 72

Wisenet PRN-6400B4

Brand: Hanwha Techwin Pages: 14

BROADCAST POLLING FRAD BPF-14 BU

Brand: DCB Pages: 28

Brand: TP-Link Pages: 57

Brand: SafeHome Pages: 24

Brand: ZyXEL Communications Pages: 30

Brand: Rosco Pages: 20

Brand: V-Count Pages: 2

Brand: Digi Pages: 75

Ultra WiFi Booster

Brand: Optus Pages: 8

Brand: Wave wifi Pages: 3

CentreCOM AT-3716XL

Brand: Allied Telesis Pages: 2

Brand: Carrier Pages: 18

Brand: Qvis Pages: 233

Cheetah EtherCard-2320

Brand: Accton Technology Pages: 10

Brand: C&H Technologies Pages: 2

WRT330N - Wireless-N Gigabit Gaming Router Wireless

Brand: Linksys Pages: 92

Brand: ASTRO Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands