N-Tron 7018 Technical Instructions Download Page 30 | Manualshive

Page: 30 / 33

background image

Revision 2010-11-15

Page 30 of 33

Firmware/Config – TFTP, Continued…

In order to Download and Upload information from the PC to the switch you will need to download
and install a TFTP Server application on the PC.

We recommend using SolarWinds TFTP Server. You may download if for free from here:

http://www.solarwinds.com/products/freetools/free_tftp_server.aspx

You must also make sure that Pings are enabled on the Firewall. See Note below.

Install and setup the TFTP Server.

The status bar along the bottom of the TFTP Server window shows the TFTP Server root directory and IP
address.

The Configuration allows you to enter a directory into which your downloaded file from the switch will be
stored. The Upload Configuration on the switch will also access this directory when uploading a new
configuration. Security should also be set to both receive and Transmit files.

«
...
28
29
30
31
32
...
»

Summary of Contents for 7018


































Reviews:

No comments

Related manuals for 7018

Netlink FRX4000

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

MMAC-Plus 9F106-02

Brand: Cabletron Systems Pages: 7

Brand: Idis Pages: 31

Brand: ZyXEL Communications Pages: 116

Brand: EVOC Pages: 57

Brand: TP-Link Pages: 7

Brand: QNAP Pages: 54

Compact NVR-AS 4000

Brand: IndigoVision Pages: 38

LMP-1202M-SFP Series

Brand: ANTAIRA Pages: 2

Brand: Comet Labs Pages: 11

Brand: Talent Pages: 18

Brand: US Robotics Pages: 180

Brand: TP-Link Pages: 4

Brand: R3 Pages: 48

Brand: ZyXEL Communications Pages: 28

Brand: Billion Pages: 2

Brand: RadioLabs Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands