Mychef iBAKE Product Manual Download Page 23 | Manualshive

Page: 23 / 96

background image

mychefcooking.com

PRODUCT MANUAL iBAKE MAX - DT.MP.IBM.2202.2

23

7.

USE

This section will give an overview of the basic functions and all the information necessary for
the correct use of the user interface of the Mychef iBAKE MAX combi oven.

For a description of more specific functions, please refer to the help available on each
screen.

7.1.

Switching on the appliance

The appliance is switched on or off using a switch located at the bottom rear.

Once switched on, the system can be switched on or off using the circular button
START/STOP on the control panel. By switching off from the circular button START/STOP
the system will remain in standby mode. To switch off completely it is necessary to use the
switch.

In order to protect the oven from possible overheating, some protection
elements may operate even when the oven is switched off. When the oven is
at a safe temperature, they will automatically switch off.

7.1.1.

First use

Once you have connected your Mychef oven for the first time, the appliance must access
the Wi-Fi network to synchronise with the cloud. It will then run a check for available software
updates and if necessary download and update the system.

After the software verification, the user interface will guide you to the "User Mode" option
to proceed to the oven registration for personalised assistance from Mychef's technical
service.

To start using the oven, it will also be necessary for the installer to register, check the serial
number and verify the oven's functionalities and ensure that the installation has been carried
out correctly. To do this, the installer must select the "Installer mode" option and follow the
steps marked by the user interface.

«
...
21
22
23
24
25
...
»

Summary of Contents for iBAKE

































































































Reviews:

No comments

Related manuals for iBAKE

Brand: PALSON Pages: 84

Brand: FCI Home Appliances Pages: 96

Brand: Midea Pages: 27

Brand: Sunbeam Pages: 28

Brand: Montgomery Ward Pages: 9

Brand: Daewoo Pages: 40

Appliances P2B930

Brand: GE Pages: 64

Brand: Daewoo Pages: 17

Spacemaker II JEM33M

Brand: Monogram Pages: 40

Brand: Parkinson Cowan Pages: 48

Brand: V-ZUG Pages: 28

Brand: ChefLine Pages: 56

Brand: ZANKER Pages: 52

Brand: Leisure Pages: 41

Brand: Euro-Pro Pages: 6

Brand: Teka Pages: 34

ANGELO PO COMBISTAR FX

Brand: MARMON Pages: 178

B1DCC0A 0B Series

Brand: NEFF Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands