M1.1.ETA12915-ETA16915.NLFREN 06112017
4
NL
MACH
• De spanningstoevoer moet door aansluitpinnen en een aarde geleverd worden, die zich in de schakelkast bevinden.
Om uw machine te beschermen wordt het gebruik van een spanningsstabilisator sterk
aanbevolen, vooral bij onstabiele spannning.
De fabrikant kan niet verantwoordelijk gesteld worden in geval van schade aan de machine als gevolg van een
onstabiele spanning.
1. Steek de stekker in het stopcontact.
2. Schakel de machine in door op de ON/OFF knop op de bedieningsdoos te drukken.
3. Druk op de FOR (vooruit) knop gedurende 5-10 seconden en laat de machine draaien. Druk op de EBR (achteruit) knop
gedurende 5-10 seconden en laat de machine draaien.
Tap niet tijdens deze test
.
4 De machine installeren
Voor installatie
1. Controleer bij de levering dat het product volledig en niet beschadigd is. Informeer uw verdeler onmiddellijk in geval van
een probleem.
2. De Installatieplaats moet perfect vlak en goed verlicht zijn.
3. Maak zeker dat de werkruimte schoon is en vrij van obstakels, die de stabiliteit van de machine kunnen beïnvloeden.
A
B
C
D
E
A
Chuck box with 6 chucks and adjusting wrench
1 set
B
Install screw for machine base
3 pcs
C
Wire casing and screw
4 pcs
D
Install screw for motor
2 pcs
E
Power line and plug
1 pcs
F
Operation Instruction
1 set
Before proceeding to install machine
1. Inspect the delivery for completeness and obvious signs of damage. Report
an incomplete or damaged delivery to your supplier/retailer immediately.
2. The machine location area must have an even surface and be perfectly
lighted.
3. Be sure that the place is clean and particle free, which could alter the
machine stability.
Installing machine steps
1. Drilling fix hole on the working table. The size and distance of the hole as
following picture. Be sure it is strictly as same as drawing required.
2. Install and fix arms with foundation on the working table by 3 pcs screw
( Delivery contents
B
).
3. Take motor and control box out, install and fix motor head on the arm by 2
pcs screw ( Delivery contents
D
).
1
Servo Motor
2
FOR/EBR key
3
Gearbox
4
Spindle
5
Chuck
6
Tapping Arm
7
Movable Joint
8
Control Box
9
Fix Base
Machine Overview
Delivery Contents
Installing Machine
6
5
A
B
C
D
E
A
Chuck box with 6 chucks and adjusting wrench
1 set
B
Install screw for machine base
3 pcs
C
Wire casing and screw
4 pcs
D
Install screw for motor
2 pcs
E
Power line and plug
1 pcs
F
Operation Instruction
1 set
Before proceeding to install machine
1. Inspect the delivery for completeness and obvious signs of damage. Report
an incomplete or damaged delivery to your supplier/retailer immediately.
2. The machine location area must have an even surface and be perfectly
lighted.
3. Be sure that the place is clean and particle free, which could alter the
machine stability.
Installing machine steps
1. Drilling fix hole on the working table. The size and distance of the hole as
following picture. Be sure it is strictly as same as drawing required.
2. Install and fix arms with foundation on the working table by 3 pcs screw
( Delivery contents
B
).
3. Take motor and control box out, install and fix motor head on the arm by 2
pcs screw ( Delivery contents
D
).
1
Servo Motor
2
FOR/EBR key
3
Gearbox
4
Spindle
5
Chuck
6
Tapping Arm
7
Movable Joint
8
Control Box
9
Fix Base
Machine Overview
Delivery Contents
Installing Machine
6
5
Leveringsomvang
A
Doos met 6 taphouders en instelsleutel
1 set
B
Basis bevestigingsschroef
3 st.
C
Handgreep
1 st.
D
Kabeldoorgang en schroef
4 st.
E
Motor bevestigingsschroef
2 st.
F
Stroomkabel en stekker
1 st.
G
Handleiding
1 st.
A
B
C
D
E
A
Chuck box with 6 chucks and adjusting wrench
1 set
B
Install screw for machine base
3 pcs
C
Wire casing and screw
4 pcs
D
Install screw for motor
2 pcs
E
Power line and plug
1 pcs
F
Operation Instruction
1 set
Before proceeding to install machine
1. Inspect the delivery for completeness and obvious signs of damage. Report
an incomplete or damaged delivery to your supplier/retailer immediately.
2. The machine location area must have an even surface and be perfectly
lighted.
3. Be sure that the place is clean and particle free, which could alter the
machine stability.
Installing machine steps
1. Drilling fix hole on the working table. The size and distance of the hole as
following picture. Be sure it is strictly as same as drawing required.
2. Install and fix arms with foundation on the working table by 3 pcs screw
( Delivery contents
B
).
3. Take motor and control box out, install and fix motor head on the arm by 2
pcs screw ( Delivery contents
D
).
1
Servo Motor
2
FOR/EBR key
3
Gearbox
4
Spindle
5
Chuck
6
Tapping Arm
7
Movable Joint
8
Control Box
9
Fix Base
Machine Overview
Delivery Contents
Installing Machine
6
5
Installatie stappen
1. Boor bevestigingsgaten in de werktafel. De grootte en de afstand
tussen de gaten moeten perfect met de tekening hiernaast
overeenstemmen.
2. Installeer en bevestig de arm met de basis op de werktafel door
middel met 3 schroeven (
B
in de leveringsomvang).
3. Pak de motor en bedieningsdoos uit, instaleer en bevestig de
motorkop op de arm met 2 schroeven (
D
).
4. Installeer 3 sets kabeldoorgang en schroef (
C
).
5. Maak de statische lijn van de arm los, breng de arm naar zijn
hoogste positie en schuif de kabel in de kabeldoorgang.
Test na installatie
AANDACHT!
• De standaard spanning is een 230 V unidirectionele
spanning. Maak zeker dat de netspanning overeenstemt met
deze die op de machine vermeld wordt.
copyrighted
document
- all
rights
reserved
by
FBC