MuxLab MuxStream 500930 Operation Manual Download Page 2

Page: 2 / 47

MuxStream Camera Operation Manual

Preface

Thank you for purchasing the MuxLab MuxStream Camera. This manual covers the camera functions,

installation and operation. Prior to installation and usage, please read the manual thoroughly.

Precautions

This product must be used in the specified conditions in order to avoid damage to the camera:

⚫

Do not subject the camera to rain or moisture.

⚫

Do not remove the cover, otherwise you may get an electric shock and may void the

warranty. In case of abnormal operation, contact the seller.

⚫

Never operate beyond the specified temperature, humidity and power supply range.

⚫

Please use a soft dry cloth to clean the camera. If the camera is very dirty, clean it with a

diluted neuter detergent; do not use any type of solvents which may damage the surface.

Note

This is class A product. Electromagnetic radiation at the specific frequency may affect the image quality

of a TV in a home environment

Copyright Notice

All contents in this manual is copyrighted, and cannot be cloned, copied or translated without the express

permission of MuxLab Inc. Product specifications and information in this document are for reference

only, and the content may be updated from time to time without prior notice.

Summary of Contents for MuxStream 500930
















































Search results

Summary of Contents for MuxStream 500930

Reviews:

Related manuals for MuxStream 500930

Brands by name

Popular brands

MuxLab MuxStream 500930, Operation Manual

Search results

Summary of Contents for MuxStream 500930

Reviews:

Related manuals for MuxStream 500930

Brands by name

Popular brands